Yamaha DSP5D Pm5dv2 / Dsp5d Editor Owner's Manual - Page 78

MIX 1-24, MATRIX 1-8, AL/AR, BL/BR, STEREO A bus L/R channels

Get Yamaha DSP5D PDF manuals and user guides View all Yamaha DSP5D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

• HPF (high pass filter) / LPF (low pass filter) Here you can make settings for the HPF/LPF that will process the pink noise or burst noise. The upper knob sets the cutoff frequency (20 Hz-20 kHz), and the lower button turns it on/off. • WIDTH/INTERVAL If burst noise is selected, these specify the length of the actual noise (WIDTH), and the length of the silent interval between noise bursts (INTERVAL). The range for WIDTH is 0.1-10 sec, and the range for INTERVAL is 1-30 seconds. (The current setting is shown by the numerical box located above the knob.) Level INTERVAL Pink noise output WIDTH The BURST NOISE button is on Time • OSC OUT (oscillator direct output) This indicates the output jack or slot channel from which the oscillator signal will be directly output. To change the output destination, click the PATCH button to access the OUTPUT PATCH window. If SINE WAVE 2CH is selected, the L-channel of the oscillator will be output from the oscillator direct output. • BUS ASSIGN Here you can select the bus that will output the sine wave or noise. (Multiple choices are allowed.) MIX 1-24 MIX buses 1-24 MATRIX 1-8 MATRIX buses 1-8 AL/AR STEREO A bus L/R channels BL/BR STEREO B bus L/R channels If SINE WAVE 2CH is selected, the L-channel of the oscillator will be output from the odd-numbered bus or the L jack, and the R-channel of the oscillator will be output from the even-numbered bus or the R jack. 78 PM5DV2/DSP5D Editor Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
PM5DV2/DSP5D Editor Owner’s Manual
78
• HPF (high pass filter) / LPF (low pass filter)
Here you can make settings for the HPF/LPF that will process the pink noise or burst noise. The upper knob
sets the cutoff frequency (20 Hz–20 kHz), and the lower button turns it on/off.
• WIDTH/INTERVAL
If burst noise is selected, these specify the length of the actual noise (WIDTH), and the length of the silent
interval between noise bursts (INTERVAL).
The range for WIDTH is 0.1–10 sec, and the range for INTERVAL is 1–30 seconds. (The current setting is
shown by the numerical box located above the knob.)
• OSC OUT (oscillator direct output)
This indicates the output jack or slot channel from which the oscillator signal will be directly output. To
change the output destination, click the PATCH button to access the OUTPUT PATCH window.
If SINE WAVE 2CH is selected, the L-channel of the oscillator will be output from the oscillator direct output.
• BUS ASSIGN
Here you can select the bus that will output the sine wave or noise. (Multiple choices are allowed.)
MIX 1–24
.................
MIX buses 1–24
MATRIX 1–8
............
MATRIX buses 1–8
AL/AR
.......................
STEREO A bus L/R channels
BL/BR
.......................
STEREO B bus L/R channels
If SINE WAVE 2CH is selected, the L-channel of the oscillator will be output from the odd-numbered bus or
the L jack, and the R-channel of the oscillator will be output from the even-numbered bus or the R jack.
INTERVAL
WIDTH
Level
Time
Pink noise output
The BURST NOISE button is on