Yamaha DSP5D Pm5dv2 / Dsp5d Editor Owner's Manual - Page 34

ATO ST To stereo BTO ST PAN To stereo pan CLCR DCSR Center Side Ratio EBALANCE FON GFader HCUE

Get Yamaha DSP5D PDF manuals and user guides View all Yamaha DSP5D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

❏ Pan / Fader A TO ST (To stereo) This is an on/off switch for the signal sent from the MIX channel to the STEREO bus. The PRE button located below selects PRE (immediately before the MIX [ON] key) or POST (immediately after the MIX [ON] key) as the point from which the signal is sent from the MIX channel to the STEREO bus. B TO ST PAN (To stereo pan) Sets the panning of the signal sent from the MIX channel to the STEREO bus. C LCR 1 Turns LCR mode on/off for each channel. If this is turned on for a channel, you can use the TO ST PAN (2) knob to simultaneously control the level of the signal sent to the STEREO bus L/R channels and CENTER channel. D CSR (Center Side Ratio) 2 This adjusts the level ratio (0-100%) of the CENTER channel relative to the STEREO bus L/R channels. To change the value, drag upward or downward inside the numerical box. E BALANCE This adjusts the left/right output balance of paired channels. This is not shown if pair- 3 ing is not specified. 4 F ON Switches the MIX channel on/off. This is linked with the MIX [ON] keys in the MIX 5 section of the PM5D panel. G Fader Adjusts the output level of the MIX channel. This is linked with the MIX encoders on the PM5D panel (if the [MIX MASTER] key is on). The current value is shown in the numerical box immediately below. A level meter is shown beside the fader. 6 H CUE This button cue-monitors the signal of the MIX channel. This is linked with the MIX [CUE] keys in the MIX section of the PM5D panel. If SOLO is active, this will function as SOLO. 7 8 34 PM5DV2/DSP5D Editor Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
PM5DV2/DSP5D Editor Owner’s Manual
34
❏
Pan / Fader
A
TO ST (To stereo)
This is an on/off switch for the signal sent from the MIX channel to the STEREO bus.
The PRE button located below selects PRE (immediately before the MIX [ON] key) or
POST (immediately after the MIX [ON] key) as the point from which the signal is sent
from the MIX channel to the STEREO bus.
B
TO ST PAN (To stereo pan)
Sets the panning of the signal sent from the MIX channel to the STEREO bus.
C
LCR
Turns LCR mode on/off for each channel. If this is turned on for a channel, you can use
the TO ST PAN (
2
) knob to simultaneously control the level of the signal sent to the
STEREO bus L/R channels and CENTER channel.
D
CSR (Center Side Ratio)
This adjusts the level ratio (0–100%) of the CENTER channel relative to the STEREO
bus L/R channels. To change the value, drag upward or downward inside the numerical
box.
E
BALANCE
This adjusts the left/right output balance of paired channels. This is not shown if pair-
ing is not specified.
F
ON
Switches the MIX channel on/off. This is linked with the MIX [ON] keys in the MIX
section of the PM5D panel.
G
Fader
Adjusts the output level of the MIX channel. This is linked with the MIX encoders on
the PM5D panel (if the [MIX MASTER] key is on). The current value is shown in the
numerical box immediately below. A level meter is shown beside the fader.
H
CUE
This button cue-monitors the signal of the MIX channel. This is linked with the MIX
[CUE] keys in the MIX section of the PM5D panel. If SOLO is active, this will function
as SOLO.
1
2
3
4
5
6
7
8