Canon 1321B002AB User Manual

Canon 1321B002AB Manual

Get Canon 1321B002AB PDF manuals and user guides View all Canon 1321B002AB manuals
Add to My Manuals
Save this manual to your list of manuals

Canon 1321B002AB manual content summary:

  • Canon 1321B002AB | User Manual - Page 1
    Document Scanner User Manual Please read this manual before operating this scanner. After you finish reading this manual, store it in a safe place for future reference.
  • Canon 1321B002AB | User Manual - Page 2
    their respective owners. Copyright Copyright 2006 by CANON ELECTRONICS INC. All rights reserved. No part of this publication may be reproduced or CANON ELECTRONICS INC. Disclaimers The information in this document is subject to change without notice. CANON ELECTRONICS INC. MAKES NO WARRANTY
  • Canon 1321B002AB | User Manual - Page 3
    parts Chapter 2 Setup Scanner operation environment and setup procedures Chapter 3 Basic Operation Supported document types, basic scanning procedure, steps for clearing a paper jam Chapter 4 Maintenance Procedures for regular maintenance, roller replacement Chapter 5 Troubleshooting Troubleshooting
  • Canon 1321B002AB | User Manual - Page 4
    symbols are used in this manual to explain procedures, restrictions, handling precautions, and instructions that should be observed for safety explanations for a procedure. Reading these notes is highly recommended. (See "Documents," on p. 3-1) Shows the page number and title of a section that
  • Canon 1321B002AB | User Manual - Page 5
    Document Scanner User Manual Hardware
  • Canon 1321B002AB | User Manual - Page 6
    Safety Instructions 1-1 Installation Location 1-1 Power ...1-2 Moving the Scanner 1-2 Handling ...1-3 Disposal...1-4 Features of the DR-4010C Document Scanner 1-5 Names and Functions of Parts 1-7 Setup ...2-1 Setup Procedure 2-1 Installation Requirements 2-2 Installing the Software 2-4 Setup
  • Canon 1321B002AB | User Manual - Page 7
    Troubleshooting 5-1 5-1 Troubleshooting 5-1 5-2 Uninstalling Software 5-6 Uninstalling the ISIS/TWAIN Driver 5-7 Uninstalling the Job Registration Tool 5-8 Uninstalling CapturePerfect 3.0 5-10 Chapter 6 Appendix ...6-1 6-1 Specifications 6-1 Specifications 6-1 Replacement Parts 6-2 Options
  • Canon 1321B002AB | User Manual - Page 8
    space around the scanner for operation, maintenance, and ventilation. At least 3.9" (100 mm) when eject tray is empty. 15.7" (400 mm) when the document feed tray and document feed tray extension are closed. 25.6" (650 mm) when the document feed tray and document feed tray extension are open
  • Canon 1321B002AB | User Manual - Page 9
    can be disconnected easily in an emergency. • If you have any questions regarding the power supply, contact your local authorized Canon dealer or service representative for further information. Moving the Scanner • When moving the scanner, always hold it with both hands to avoid dropping it. The
  • Canon 1321B002AB | User Manual - Page 10
    power switch OFF, and disconnect the power plug from the power outlet. Then, contact your local authorized Canon dealer or service representative to have the unit serviced. ■ Before moving the scanner, be sure to turn the power switch OFF, and disconnect the power plug from the power outlet. CAUTION
  • Canon 1321B002AB | User Manual - Page 11
    used for an extended period of time, such as during consecutive holidays. ■ Do not wear loose clothing or jewelry that may get caught in the scanner while you are using it. This may result in personal injury. Be extra careful of neckties and long hair. If anything becomes caught in the
  • Canon 1321B002AB | User Manual - Page 12
    Supports a Variety of Scanning Modes The scanner supports the following scanning modes, depending on the document type: - Single-sided/double-sided mode - Single sheet/dual feeding path • U-Turn Path Documents are fed and ejected from the front of the scanner. (See "3-2 Document Feed and Eject Tray
  • Canon 1321B002AB | User Manual - Page 13
    send the adjusted image to the application software, without needing to scan the document again. • Remove Binder Holes This mode erases the black spots that appear on scanned images from binding holes on the original document. • MultiStream Function The scanner supports MultiStream, which, according
  • Canon 1321B002AB | User Manual - Page 14
    the parts of the scanner before using the scanner. ■ Front View (Feed Tray Open) Document Eject Tray Extension Open if the document extends beyond the edge of the eject tray. (See p. 3-3.) Document Feed Tray Place the document to be scanned here. (See p. 3-3.) Document Eject Tray Scanned documents
  • Canon 1321B002AB | User Manual - Page 15
    Scanner ■ Back View Document Eject Tray 2 Open this tray to use the scanner in a straight path configuration. (See p. 3-3.) ■ Interfaces (See "2-4 Connecting the Scanner supports Hi-Speed USB 2.0. Power Connector CAUTION • Do not block the ventilation openings. Doing so could cause the scanner
  • Canon 1321B002AB | User Manual - Page 16
    order to prepare the scanner for use, read and follow the instructions in each section below. Installation Requirements Installing the Software Connecting the Scanner to the Computer Turning the Power ON IMPORTANT • Be sure to install the software before connecting the scanner to the computer. • If
  • Canon 1321B002AB | User Manual - Page 17
    Installation Requirements To use the DR-4010C scanner, your computer must satisfy the following system requirements. • One of the following operating systems: - Microsoft Windows 2000 Professional SP4 or later - Microsoft Windows XP Professional SP2 or later - Microsoft Windows XP Home Edition SP2
  • Canon 1321B002AB | User Manual - Page 18
    and transmission may take a long time. • Even if the computer satisfies the recommended specifications, the scanning speed may vary, depending on the scan settings. • The ISIS/TWAIN Drivers provided with the scanner do not necessarily operate on all ISISor TWAIN-compatible applications. For details
  • Canon 1321B002AB | User Manual - Page 19
    Note The Setup disc of the DR-4010C is configured as follows. Menu screen Typical Installation Read Manuals All of the indicated software is installed. Custom Installation The User Manual and CapturePerfect 3.0 Operation Guide electronic manuals for the scanner are installed on the computer
  • Canon 1321B002AB | User Manual - Page 20
    all of the displayed software and the User Manual will be installed automatically. If you want to reinstall only specific software that you have previously uninstalled, select [Custom Installation] and specify the software. • The DR-4010C driver installation comprises the Scanner Driver and Job Tool
  • Canon 1321B002AB | User Manual - Page 21
    Chapter 2 Setup 4 Click [Install]. Installation of the DR-4010C driver begins. 5 Click [Next]. The software license agreement appears. 6 Read the license agreement and click [Yes] to accept it. The DR-4010C driver is installed. 2-6
  • Canon 1321B002AB | User Manual - Page 22
    Chapter 2 Setup Next, the job tool software is installed. 7 The DR-4010C driver installation is complete. 8 Click [Finish]. Installation of CapturePerfect 3.0 starts. 2-7
  • Canon 1321B002AB | User Manual - Page 23
    Chapter 2 Setup 9 Click [Next]. The software license agreement appears. 10 Read the license agreement and click [Yes] to accept it. The installation location screen appears. 11 Click [Next]. CapturePerfect is installed. 12 The CapturePerfect installation is complete. 2-8
  • Canon 1321B002AB | User Manual - Page 24
    Chapter 2 Setup 13 Click [Finish]. Installation of the User Manual starts. 14 Click [Next]. The User Manual is installed. 15 The User Manual installation is complete. 16 Click [Finish]. The installation completion screen appears. 2-9
  • Canon 1321B002AB | User Manual - Page 25
    Chapter 2 Setup 17 Click [Exit]. Click [Back] to return to the menu screen. 18 After the software installation is complete, you can connect the scanner to the computer. (See "2-4 Connecting the Scanner to the Computer," on p. 2-11.) 2-10
  • Canon 1321B002AB | User Manual - Page 26
    to the Computer There are two methods for connecting the DR-4010C scanner to a computer: USB connection, which makes use of a SCSI cable at the same time. Using a USB Connection 1 Verify that the power switch of the scanner is OFF. If the power switch is in the ON position, push the switch to set it
  • Canon 1321B002AB | User Manual - Page 27
    ID numbers in the system. DIP switches Factory default (SCSI ID = 2) • The DR-4010C scanner incorporates a SCSI terminator which is permanently set to ON. When using a daisy-chain configuration with other SCSI devices, make sure that the DR4010C is connected as the last device in the chain. Set the
  • Canon 1321B002AB | User Manual - Page 28
    Chapter 2 Setup 1 Shut down Windows and turn the computer OFF. 2 Verify that the power switch of the scanner is OFF. If the power switch is in the ON position, push the switch to set it . a 4 Connect the power cord into an AC outlet. b 5 Use the SCSI cable to connect the scanner to the computer. 2-13
  • Canon 1321B002AB | User Manual - Page 29
    the scanner ON. The power indicator lights green. Power indicator Power switch ON 3 Turn the computer ON. 4 Log onto Windows with an account that has Administrator privileges. 5 Windows recognizes the DR-4010C automatically, and installation of the device driver begins. Windows 2000 Windows XP
  • Canon 1321B002AB | User Manual - Page 30
    Chapter 2 Setup Note • In Windows XP, a message appears when installation is complete. • In Windows 2000, no message appears when installation is complete. • The DR-4010C is installed in Device Manager under [Imaging Devices] as [CANON DR- 4010C USB] or [CANON DR-4010C SCSI]. 2-15
  • Canon 1321B002AB | User Manual - Page 31
    embossing (*1) The DR-4010C offers two document eject configurations: U-turn path (the document is ejected to the document eject tray at the front of the scanner) and straight path (the document is ejected to the back of the scanner.) (See "3-2 Document Tray and Eject Tray," on p. 3-3.) U-turn
  • Canon 1321B002AB | User Manual - Page 32
    can lead to smudges in the scanned image and transfer the dirt to subsequent documents. Always clean the internal parts of the scanner after scanning such documents. (See "Cleaning the Sensor Glass and the Rollers," on p. 4-2.) • When scanning a two-sided document that is printed on thin paper, the
  • Canon 1321B002AB | User Manual - Page 33
    to fall off, resulting in personal injury or damage to the scanner. Preparing the Document Eject Tray The scanner has two eject methods: documents can be ejected to the front of the scanner in a Uturn path, or to the back of the scanner in a straight path. You can switch between these methods by
  • Canon 1321B002AB | User Manual - Page 34
    thin paper, thick paper and business cards that cannot be scanned through the U-turn path. Scanned documents are ejected to the back of the scanner. • The U-turn path cannot be used if the document eject tray 2 is open. • When using the straight path, the pages are stacked in the reverse order from
  • Canon 1321B002AB | User Manual - Page 35
    of documents placed in the feed tray is called the Page Separation mode. Feeding documents one sheet at a time or feeding documents consisting , damage the document, or cause a paper jam or scanner malfunction. ■ Do not wear loose clothing or jewelry that may get caught in the scanner while you are
  • Canon 1321B002AB | User Manual - Page 36
    Chapter 3 Basic Operation CAUTION ■ Do not place the documents on top of the scanner to align them. Doing so may cause a malfunction. ■ When placing documents into the feed tray, take care not to cut your hands on the edges of the paper. 3 Adjust the document guides so that they are wider than the
  • Canon 1321B002AB | User Manual - Page 37
    the scanner is scanning, resolve the problem, make sure that the scanned image of the last page that was successfully fed has been stored, and then resume scanning the remaining document pages. • Note that documents that are printed on thin paper may fall out of the document eject tray. • After
  • Canon 1321B002AB | User Manual - Page 38
    leading edge of the documents as you feed them. Take care not to get your hand caught under the roller unit, as this may cause personal injury. Roller Unit ■ After you finish scanning, close the document feed tray and the document eject tray extension to prevent damage to the scanner while it is not
  • Canon 1321B002AB | User Manual - Page 39
    3-4 Job Function In addition to using scanning applications, such as Capture Perfect 3.0 to perform scanning, the DR4010C is equipped with the Job Function. The Job Function enables you to scan simply by touching a job button on the scanner. This section provides an overview of the Job Function and
  • Canon 1321B002AB | User Manual - Page 40
    a TWAIN-compatible application that is installed with the ISIS/TWAIN driver, and launches from the Programs menu. Use the Job Registration file: Saves scanned image data as PDF files in the [My Pictures] folder. • If you assign scan functions to all three job buttons on the scanner, use the Start
  • Canon 1321B002AB | User Manual - Page 41
    > appears on the DR-4010C monitor. 4 Click [Close] to close the DR-4010C monitor. Note • The default setting for job button c after the DR-4010C setup is completed is "Scan." • The scanned images are saved as PDF files in the folder [My Pictures] under the folder [My Documents]. The file name
  • Canon 1321B002AB | User Manual - Page 42
    from this dialog box or click [Cancel] and change the event settings. • Only applications that support the Windows event function can be started using the Launcher feature of the DR-4010C. • Some applications may not work correctly if started using the Launcher feature. Event Settings This section
  • Canon 1321B002AB | User Manual - Page 43
    Panel (Category View) Printers and Other Hardware Control Panel (Classic View) 3. Double-click [Scanners and Cameras]. 4. Select [CANON DR-4010C USB] (or [CANON DR-4010C SCSI]) Æ click [Properties]. The [CANON DR-4010C USB Properties] (or [CANON DR-4010C SCSI Properties]) window appears. 3-13
  • Canon 1321B002AB | User Manual - Page 44
    Chapter 3 Basic Operation 5. Click the [Events] tab. 2 Under [Scanner events], select the button whose setting you want to change (Button No. 1, Button No. 2, Button No. 3.) 3-14
  • Canon 1321B002AB | User Manual - Page 45
    device events] check box is selected, the Job Function cannot be used. Make sure that this check box is not selected. 4 Click [OK] to close [Scanners and Cameras Properties]. 5 Restart Windows to enable the new event settings. 3-15
  • Canon 1321B002AB | User Manual - Page 46
    -compatible application developed for Canon document scanners. CapturePerfect 3.0 includes the following modes. Select the desired scan mode from the Scan menu to perform scanning. „ Scan Batch to File Documents are scanned with the preset scanning conditions, and the scanned image data is saved to
  • Canon 1321B002AB | User Manual - Page 47
    is scanned, and the scanned image is displayed at full size on the screen. DR-4010C Projector The scanned image is projected on the screen. Using CapturePerfect 3.0 This section describes how to start up CapturePerfect 3.0, select the scanner, and scan documents. The Scan Batch to File function
  • Canon 1321B002AB | User Manual - Page 48
    to select the Canon DR-4010C Document Scanner as the scanner to be used. 1. On the [Scan] menu, click [Select Scanner]. 2. Select [Canon DR-4010C] Æ click [OK]. Note If [Canon DR-4010C] is not displayed in the list of scanners, re-install the ISIS/TWAIN driver. (See "2-3 Installing the Software," on
  • Canon 1321B002AB | User Manual - Page 49
    3 Basic Operation 3 On the [Scan] menu, click [Scanner Setting]. The Properties dialog box for the ISIS driver opens. 4 Set the scan settings. For more information on scan settings, see Chapter 7, "ISIS/TWAIN Driver Settings." 5 Place your document. (See "3-3 Placing Documents," on p. 3-5.) 3-19
  • Canon 1321B002AB | User Manual - Page 50
    documents, see the CapturePerfect 3.0 Operation Guide and CapturePerfect Online Help. 7 Specify the file name and the file type for saving the image more pages of the document to scan, scanning stops. Scanning resumes or ends according to the Feeding Option setting in the scanner setup. • Feeding
  • Canon 1321B002AB | User Manual - Page 51
    • Feeding Option is set to "Panel-Feeding": Place the next document and press job button a (Start) to resume scanning, or press application that is installed with the ISIS/TWAIN driver. When the DR-4010C driver starts, the scan panel appears in the task tray. If Feeding Option in the scan settings is
  • Canon 1321B002AB | User Manual - Page 52
    ] tab, if you enable batch separation from the application and start scanning, this button becomes active when scanning of the current document completes, and scanning stops. When clicked, this button depresses and remains depressed while scanning with batch separation continues, until scanning of
  • Canon 1321B002AB | User Manual - Page 53
    Patchcode sheets are data in a portable document format (PDF.) There are four types; [PATCH II (A4)], [PATCH II (LTR)], [PATCH T (A4)], [PATCH T (LTR)] according to the paper size and pattern. Click on the Windows start button, open [Programs] Æ [Canon DR-4010C] Æ [PATCH X (XX)]. Print the patchcode
  • Canon 1321B002AB | User Manual - Page 54
    their function changes according to their pattern. ■ PATCH T (FILE A) When the scanner recognizes this patchcode printed on a patchcode sheet, it creates a separate file for the document that comes after the patchcode sheet. The image of this sheet can be saved or not, depending on the application
  • Canon 1321B002AB | User Manual - Page 55
    Other] tab of the ISIS driver properties, set the batch If "Scan, Continue Scanning" is selected, the patchcode sheet image is also saved and scanning continues. • If "Skip, Continue T (FILE A) pattern is detected, the patchcode sheet image is not saved and scanning continues. IMPORTANT Make sure to
  • Canon 1321B002AB | User Manual - Page 56
    the paper. 1 Remove any documents that have been left in the eject tray, and close the eject tray guide. IMPORTANT If a document stops in the eject tray, remove the document before closing the document eject tray extension. Attempting to force the document eject tray extension closed may damage the
  • Canon 1321B002AB | User Manual - Page 57
    feed section ■ If the jam occurred in the eject section IMPORTANT Make sure to pull the document out carefully, without applying too much force. If jammed paper tears while it is being removed, make sure to remove any remaining pieces from inside the scanner. 4 Close the upper unit slowly. Make sure
  • Canon 1321B002AB | User Manual - Page 58
    3 Basic Operation • If a paper jam occurs when "Rapid recover system" is enabled in the ISIS/TWAIN driver settings, the image data of the document is not saved and scanning stops. This allows you to continue scanning from the document that caused the paper jam after the paper jam is fixed. 3-28
  • Canon 1321B002AB | User Manual - Page 59
    Feed Detection Function The scanner will detect a double feed and stop scanning. • Long Document Mode Allows scanning of documents up to 39.2" (1,000 mm) in length. • MultiStream Function Two types of images are output from a single scanning pass. Folio Scan This function supports the scanning of
  • Canon 1321B002AB | User Manual - Page 60
    mode, set the paper size for the ISIS/TWAIN driver to "Auto-detection" to allow the scanner to detect and scan documents up to 39.2" (1,000 mm) long. Note the following when using the Long Document mode: • Scanning documents up to 39.2" (1,000 mm) long may not be possible with some scanning modes
  • Canon 1321B002AB | User Manual - Page 61
    Follow the procedure below to set the Long Document mode. 1 Use the following procedure to open the [CANON DR-4010C USB Properties] (or [CANON DR-4010C SCSI Properties].) 1. Click [Start] Æ [Settings] on the [Start] menu Æ click [Control Panel]. (For Windows XP, click [Start] Æ click [Control Panel
  • Canon 1321B002AB | User Manual - Page 62
    Chapter 3 Basic Operation 3. Double-click [Scanners and Cameras]. 4. Select [CANON DR-4010C USB] or ([CANON DR-4010C SCSI]) Æ click [Properties]. The [CANON DR-4010C USB Properties] (or [CANON DR-4010C SCSI Properties]) window appears. 3-32
  • Canon 1321B002AB | User Manual - Page 63
    Chapter 3 Basic Operation 2 Click the [Maintenance] tab. 3 Click [Long Document mode (1,000 mm)]. 4 Click [Apply] to change the scanner's settings. 5 Click [OK] to close [Scanners and Cameras Properties]. 6 Turn the scanner OFF and then ON again. IMPORTANT • If you are using a SCSI connection, turn
  • Canon 1321B002AB | User Manual - Page 64
    using supports the MultiStream function, then it is possible to scan a document once and simultaneously output two types of images (Primary image and Secondary image.) CapturePerfect 3.0 supports the MultiStream "Auto Color Detection" is selected for the Mode setting in the ISIS/TWAIN driver. 3-34
  • Canon 1321B002AB | User Manual - Page 65
    Feed Path Dust or paper particles in the document feed opening or inside the scanner can cause lines in scanned images. Use compressed air to periodically clean dust and paper particles from the document feed opening and the inside of the scanner. After finishing a large scanning job, turn OFF the
  • Canon 1321B002AB | User Manual - Page 66
    Chapter 4 Maintenance Cleaning the Sensor Glass and the Rollers If scanned images have extraneous marks, or if the scanned documents are dirty, the sensor glass or rollers inside the scanner may be dirty. Clean them periodically. 1 Carefully open the upper unit until it stops. IMPORTANT When opening
  • Canon 1321B002AB | User Manual - Page 67
    glass, contact your local authorized Canon dealer or service representative. 4 Dampen a cloth with water, wring it out thoroughly, and then wipe the rollers of the upper unit while turning them. Do not try to turn the rollers in the lower part of the scanner. Clean these rollers simply by wiping the
  • Canon 1321B002AB | User Manual - Page 68
    Maintenance 6 Wipe the removed rollers with a cloth that has been moistened with water and thoroughly wrung out. 7 Attach the rollers that were removed. (See "Attaching the Roller Unit," on p. 4-10, and "Attaching the Retard Roller force the upper unit to close. Doing so may damage the scanner. 4-4
  • Canon 1321B002AB | User Manual - Page 69
    , and replace them if necessary before the message is displayed. • Be sure to reset the counter after replacing the rollers. (See "Resetting the Counter," on p. 4-6.) • For information about the exchange roller kit (roller unit, retard roller,) contact your local authorized Canon dealer or service
  • Canon 1321B002AB | User Manual - Page 70
    Chapter 4 Maintenance Resetting the Counter After replacing the feed rollers, open the [Counter setup] dialog box and reset the counter. 1 Open the [Event settings] dialog box. 1. Click the [Start] button, Æ [Settings] on the [Start] menu Æ click [Control Panel]. (For Windows XP, click the [Start]
  • Canon 1321B002AB | User Manual - Page 71
    Chapter 4 Maintenance 3. Double-click [Scanners and Cameras]. 4. Select [CANON DR-4010C USB] (or [CANON DR-4010C SCSI],) Æ click [Properties]. [CANON DR-4010C USB Properties] (or [CANON DR-4010C SCSI Properties]) is displayed. 4-7
  • Canon 1321B002AB | User Manual - Page 72
    Chapter 4 Maintenance 2 Click the [Maintenance] tab. 3 Click the [Reset] button, and then make sure that the counter for the roller being used is set to 0. 4-8
  • Canon 1321B002AB | User Manual - Page 73
    unit until it stops. IMPORTANT When opening the upper unit, do not grasp the roller unit in the center. Doing so may distort the rollers and lead to feeding errors. 2 Push the roller lock lever down. 3 While supporting the roller unit with your hand, slide the roller lock lever to the right. 4-9
  • Canon 1321B002AB | User Manual - Page 74
    4 Maintenance 4 Move the roller unit to the right a and then pull it out b. Attaching the Roller Unit 1 Align the cutout on the roller unit with the shaft pin on the main unit. Note If the cutout and pin do not fit, rotate the roller until the parts are properly matched. 2 Slide the roller lock
  • Canon 1321B002AB | User Manual - Page 75
    Chapter 4 Maintenance 4 Carefully lower the upper unit. Finally, push the upper unit force the upper unit to close. Doing so may damage the scanner. Removing and Attaching the Retard Roller To remove or attach the retard roller, proceed as follows. CAUTION Do not use excessive force when removing
  • Canon 1321B002AB | User Manual - Page 76
    ends of the roller cover and remove the cover. 3 Move the roller lock lever down and forward (a,) and then slide it to the right (b.) 4 Shift the retard roller to the right to remove it. Attaching the Retard Roller 1 Position the retard roller so the notch in the roller is facing the scanner's shaft
  • Canon 1321B002AB | User Manual - Page 77
    Chapter 4 Maintenance 2 Slide the roller lock lever to the left, and insert it into the retard roller slot. 3 Push the roller lock lever towards the back of the scanner to lock the retard roller into place. 4 Replace the roller cover. 5 Push the center of the roller cover down and make sure that it
  • Canon 1321B002AB | User Manual - Page 78
    Chapter 4 Maintenance 6 Close the upper unit slowly. Make sure that the upper unit is completely closed by pushing on both edges with both hands until you your fingers caught, as this may result in personal injury. IMPORTANT Do not force the upper unit to close. Doing so may damage the scanner. 4-14
  • Canon 1321B002AB | User Manual - Page 79
    Speed P.5-3 Documents Do Not Feed Properly P.5-3 Saved Image Files Do Not Open P.5-4 Scanning Results Are Not as Expected P.5-4 If, after consulting this section, you still cannot resolve the problem, contact your local authorized Canon dealer or your service representative. ✘ The Scanner Does
  • Canon 1321B002AB | User Manual - Page 80
    p. 2-2.) ✘ Scanning Is Not Performed Check the following if the scanner does not scan an image even though the scanning operation is performed: • Has the application software been installed correctly? Has the application software been set up correctly? • Is there a problem in the PC system? 5-2
  • Canon 1321B002AB | User Manual - Page 81
    5 Troubleshooting IMPORTANT • If documents are not scanned normally even if the scanner setup is OK, a probable cause is that the scanner driver or application software is not running correctly. Re-install the scanner driver or application software. • When system errors result in the scanner not
  • Canon 1321B002AB | User Manual - Page 82
    Documents," on p. 3-1. Problem Solution The rollers inside the scanner are dirty or worn. Clean the rollers, see "4-1 Regular Maintenance," on p. 4-1. If the rollers are worn, then they need to be replaced. Contact your local authorized Canon dealer or service representative to purchase a roller
  • Canon 1321B002AB | User Manual - Page 83
    after cleaning the scanning glass and rollers, the scanning glass inside the scanner may be scratched. Contact your local authorized Canon dealer or service representative. Symptoms Problem Solution The scanned image is abnormal for certain documents. Functions such as [Auto-detection], [Deskew
  • Canon 1321B002AB | User Manual - Page 84
    Chapter 5 Troubleshooting 5-2 Uninstalling Software If the ISIS/TWAIN driver, and "CapturePerfect 3.0" are not operating normally, follow the procedure below to uninstall them. Then, re-install the software from the DR-4010C setup disc. (See "2-3 Installing the Software," on p. 2-4.) IMPORTANT Be
  • Canon 1321B002AB | User Manual - Page 85
    Chapter 5 Troubleshooting The [Add/Remove Programs Properties] dialog box appears. Note For Windows XP, the [Add or Remove Programs] dialog on p. 5-10. Uninstalling the ISIS/TWAIN Driver 1 From the Programs list in the dialog box, select [Canon DR-4010C Driver] Æ click the [Change/Remove] button.
  • Canon 1321B002AB | User Manual - Page 86
    Chapter 5 Troubleshooting The uninstall procedure is carried out. 3 After uninstall is complete, click the [Finish] button to exit the uninstaller. Uninstalling the Job Registration Tool 1 From the Programs list in the dialog box, select [DR-4010C Job Registration Tool] and click the [Change/Remove]
  • Canon 1321B002AB | User Manual - Page 87
    Chapter 5 Troubleshooting 2 The [Confirm File Deletion] screen appears. Click the [Yes] button. The [Remove Shared File?] dialog box appears. 3 Click the [Yes To All] button. A confirmation message appears. Note Under Windows XP, the [Add/Remove Programs] dialog box appears. 4 Click the [Yes] button
  • Canon 1321B002AB | User Manual - Page 88
    Chapter 5 Troubleshooting 5 After uninstall is complete, click the [OK] button to exit the uninstaller. Uninstalling CapturePerfect 3.0 1 Select [CapturePerfect 3.0] from the list in the dialog box Æ click the [Remove] button. 5-10
  • Canon 1321B002AB | User Manual - Page 89
    Chapter 5 Troubleshooting 2 The file delete confirmation screen appears. Click the [Yes] button. Uninstallation starts. 3 After uninstallation is complete, click the [Finish] button to exit the uninstaller. 5-11
  • Canon 1321B002AB | User Manual - Page 90
    0.66 mm) Business cards are supported. However, scanning embossed cards is not guaranteed. Size: Thickness: 2.12" × 3.37" (53.9 mm × 85.5 mm) 0.03" ± 0.003" (0.76 ± 0.08 mm) Document Feeding Method Automatic/Manual Scanning Method Color 3-line contact image sensor Light Source LED Effective
  • Canon 1321B002AB | User Manual - Page 91
    on your software. Due to our ongoing efforts to improve our products, the specifications described above are subject to change without notice. Replacement Parts Exchange roller kit (product code: 1921B001) Kit to replace the roller unit (pickup roller, feed roller) and retard roller. • Refer to
  • Canon 1321B002AB | User Manual - Page 92
    External Dimensions 12.5" (318 mm) 10.9" (278 mm) 21.4" (544 mm) (Document Feed Tray Extension is open) 19.3" (491 mm) (Document Feed Tray is open) 12.9" (330 mm) (Document Eject Guide is open) 2.0" (51 mm) (Document Eject Tray 2 is open) 8.9" (225 mm) 5.2" (131 mm) 4.7" (119 mm) 2.9" (76 mm
  • Canon 1321B002AB | User Manual - Page 93
    -chain configuration 2-12 DIP switches 2-12 Disposal 1-4 document eject configurations 3-1 document feed tray 3-7 document guides 3-6 Documents 3-1 Double Feed Detection Function 3-30 DR-4010C monitor 3-11 E Eject Tray 3-3 event 3-11 Event settings 4-6 External Dimensions 6-3 F Features
  • Canon 1321B002AB | User Manual - Page 94
    Document Scanner User Manual Software
  • Canon 1321B002AB | User Manual - Page 95
    9 ISIS/TWAIN Driver Settings 7-1 Before Use 7-1 ISIS/TWAIN Driver Properties Dialog Box 7-3 Basic Tab Sheet 7-4 [Brightness] Tab Sheet 7-13 [Image processing] Tab Non-Standard-Size Documents 9-1 Adjusting the Scan Area 9-2 Scanning Multiple Documents 9-3 Image Adjustments for Scanning
  • Canon 1321B002AB | User Manual - Page 96
    the ISIS/TWAIN driver's Help before making driver settings. 7-1 Before Use This scanner can scan documents ranging in size from business cards and checks to A4 size documents. It can also scan business cards. To use the DR-4010C with an ISIS/TWAIN-compliant application, the DR-4010C must first be
  • Canon 1321B002AB | User Manual - Page 97
    2 On the [Scan] menu, click [Select Scanner]. 3 Select [Canon DR-4010C] Æ click the [OK] button. Note If [Canon DR-4010C] is not displayed in the list of scanners, re-install the ISIS/TWAIN driver. 4 Click the [Settings] button to set a default page size. Note • Clicking the [Default] button
  • Canon 1321B002AB | User Manual - Page 98
    properties dialog box consists of four tabs: Basic, Brightness, Image processing and Others. See the description of each tab sheet for details. [OK] Button Applies settings and closes the dialog box. [Scan] Button (TWAIN driver only) To control scanning from the properties dialog box when using
  • Canon 1321B002AB | User Manual - Page 99
    ) This [Basic] tab sheet is displayed when the DR-4010C ISIS Driver is called from a scanner setting or scanning dialog box belonging to an ISIS-compatible application program. This [Basic] tab sheet provides settings for DR-4010C functions that are not supported in the dialog box belonging to the
  • Canon 1321B002AB | User Manual - Page 100
    Chapter 7 ISIS/TWAIN Driver Settings ☞ Refer to the descriptions of the following function for details different background types. Select the mode that seems to best suit your document. We recommend confirming an image by prescanning the first page. [Black and White] Use this mode to scan text
  • Canon 1321B002AB | User Manual - Page 101
    this may be a problem, try scanning again after cleaning the scanner glass, or select one of the [Advanced Text Enhancement] or [Advanced Text Enhancement II] modes instead. [256-level Gray] Scans documents such as photos as 256-level grayscale images. [24-bit Color] Scans documents such as color
  • Canon 1321B002AB | User Manual - Page 102
    Tab sheet Basic Image processing Others Prescan Batch Separation JPEG Transfer Color drop-out Reverse Image (TWAIN driver) Prevent Bleed area at the left or right edge • When scanning a glossy or reflective document • When the brightness setting is incorrect • When Custom setting is selected in
  • Canon 1321B002AB | User Manual - Page 103
    side of documents loaded at the feeder inlet. [Duplex] Scan both sides of documents. [Skip Blank Page] As each document page is scanned, its scanned image is judged option is selected in the [Others] tab sheet of the TWAIN driver, the [Simplex] scanning side setting is selected automatically. ☞ If
  • Canon 1321B002AB | User Manual - Page 104
    cases, depending on the document, the slant of the image may not be corrected properly or part of the image may be omitted. Moire time, a portion of the document may not be scanned due to insufficient memory on the scanner. If this occurs, lower the image quality by selecting [Speed priority],
  • Canon 1321B002AB | User Manual - Page 105
    ] (TWAIN driver only) Specify operation when scanning continuously with a TWAIN-compatible application. [Standard image] Eject a scanned time, a portion of the document may not be scanned due to insufficient memory on the scanner. If this occurs, lower the image quality by selecting [Speed priority
  • Canon 1321B002AB | User Manual - Page 106
    scan on a selected page size, and register non-standard document page sizes. The Scan Area dialog box is different for ISIS and TWAIN drivers: for the TWAIN driver, one of two dialog box types is displayed depending on the application program used. Scan Area Dialog Box (ISIS Driver) Area window 7-11
  • Canon 1321B002AB | User Manual - Page 107
    Settings Scan Area Dialog Box (TWAIN Driver) This dialog box appears with application programs that display the [Scan] button in the Properties dialog box. Area window The Area window and [Preview] button are not displayed when using applications like the Job Registration Tool that display the
  • Canon 1321B002AB | User Manual - Page 108
    is not possible on the extended version of the [Basic] tab sheet (P.7-4.) Preview Button (TWAIN driver only) Click the [Preview] button to scan one document page and display its preview image in the Area window. [Brightness] Tab Sheet On the [Brightness] tab sheet, you can adjust brightness and
  • Canon 1321B002AB | User Manual - Page 109
    Chapter 7 ISIS/TWAIN Driver Settings The availability of brightness and contrast settings White], and selecting it adjusts brightness and contrast to match the document. Brightness Adjusts the brightness of images to be scanned. ☞ If images are too dark or if text on the back bleeds through, you
  • Canon 1321B002AB | User Manual - Page 110
    Chapter 7 ISIS/TWAIN Driver Settings [Gamma Settings] Dialog Box Use the [Gamma Settings] Select Select the side and color for custom setting. ☞ The color bar and color of the sample image are changed to show the specified color. Input method Select the setting method for gamma correction. [Factor
  • Canon 1321B002AB | User Manual - Page 111
    Chapter 7 ISIS/TWAIN Driver Settings ☞ You can also move the gamma curve by dragging it with the mouse. [Freehand] The output value for a particular input value in the gamma
  • Canon 1321B002AB | User Manual - Page 112
    depending on the mode settings on the [Basic] tab sheet. Refer to "ModeDependent Function Limitations," on p. 7-7 for details. [Reverse Image] Check Box (TWAIN driver only) The document is scanned with black and white reversed when scanning in black and white (binary) mode. [Edge Emphasis] Adjusts
  • Canon 1321B002AB | User Manual - Page 113
    selected, [Image Rotation] and area settings in the Scan Area dialog box are disabled. ☞ Some application programs do not support [Text Reverse Image] Check Box (TWAIN driver only) Select this check box to reverse (swap) black and white when scanning documents as black and white (binary) images.
  • Canon 1321B002AB | User Manual - Page 114
    you specify may not match those processed. [Others] Tab Sheet The settings on the [Others] tab sheet are different for the ISIS and TWAIN drivers. Also, some settings may be disabled depending on the mode settings on the [Basic] tab sheet. Refer to "ModeDependent Function Limitations," on p. 7-7 for
  • Canon 1321B002AB | User Manual - Page 115
    for output to the computer. Scanned image data is output from the scanner as an uncompressed or JPEG transfer, depending on instructions from the ISIS/TWAIN driver or application program. ☞ Uncompressed transfers output raw scanned image data, so when the image data is large, significant time may
  • Canon 1321B002AB | User Manual - Page 116
    with different-size pages, after loading the documents, you can adjust the document guide position. [Automatic Feeding] This feeding method is good for scanning batches of same-size documents: scanning starts when the scanner detects loaded documents, and stops when you press the Stop button
  • Canon 1321B002AB | User Manual - Page 117
    Driver Settings With the [Standard Feeding] Feeding Option With the [Automatic Feeding] or [Panel Feeding] Feeding Option [Auto] Each batch of documents is saved with different file names. [Panel] Document sheet is detected between documents. (See "3-6 driver on document pages first document page
  • Canon 1321B002AB | User Manual - Page 118
    the optional barcode module is installed: click it to open the Barcode dialog box and make settings affecting barcode detection in documents. For details, see the ISIS/TWAIN driver Help, or contact your supplier. [Addon] Button This button opens the [Addon] dialog box, where you can make setting for
  • Canon 1321B002AB | User Manual - Page 119
    7 ISIS/TWAIN Driver Settings Addon Dialog Box The [Addon] dialog box provides access to the following dialog boxes, where you can make setting for adding text or bitmap images to scanned document images. The [Addon] dialog box enables you to make setting for adding text or bitmap images to scanned
  • Canon 1321B002AB | User Manual - Page 120
    Chapter 7 ISIS/TWAIN Driver Settings [Addon] Check Box Select this check box to apply text or bitmap images to scanned document images. Imprinter Side Select the side on which to apply your text or images. [Enable] Check Box Select this check box to enable the application of add-on text. Text Enter
  • Canon 1321B002AB | User Manual - Page 121
    Chapter 7 ISIS/TWAIN Driver Settings [Left arrow] abbreviation: Inserts a left arrow () symbol. [Right arrow] abbreviation: Inserts a right arrow ( ) symbol. ☞ Special text can only be entered for one type of
  • Canon 1321B002AB | User Manual - Page 122
    Chapter 7 ISIS/TWAIN Driver Settings ☞ When add-on text is applied to an image, the size of the characters depends on the scan resolution. [Enable] Check Box Select this check box to enable application of bitmap images to scanned images. ☞ When adding a bitmap image, it is processed when scanning is
  • Canon 1321B002AB | User Manual - Page 123
    Chapter 7 ISIS/TWAIN Driver Settings [Horizontal Offset] Enter the desired offset from the edge of the document feeder inlet. ☞ When applying it is applied. ☞ An error message may appear depending on the size of the image file. If this happens, reduce the Print width. First Counter This is the
  • Canon 1321B002AB | User Manual - Page 124
    Value Select the initial value when the counter is reset. Reset Trigger Specifies the type of event that resets the counter. [New File] (ISIS driver only) The counter is reset when a batch separation occurs according to the Batch Separation settings on the [Others] tab sheet. (See "Batch Separation
  • Canon 1321B002AB | User Manual - Page 125
    is a TWAIN-compliant application program that installs with the ISIS/ TWAIN driver, and is started by the following procedure. 1 Click the Windows [Start] button, and click then [Programs] ([All Programs] for Windows XP) Æ [DR-4010C] Æ [Job Registration Tool]. The Job Registration Tool starts. (See
  • Canon 1321B002AB | User Manual - Page 126
    provides access to function setting dialog boxes. (See "[New/Editing] Dialog Box," on p. 8-4.) Job Registration Tool Dialog Box (p. 8-3) [Admin] Dialog Box (p. 8-8) [New/Editing] Dialog Box (p. 8-4) Scanner Settings Dialog Box Access Setting PDF/TIFF Settings 8-2
  • Canon 1321B002AB | User Manual - Page 127
    the Job Registration Tool is started from the Programs menu. Job Button Settings List The displayed job buttons correspond to those on the scanner, showing their currently assigned settings. Clicking on the job buttons (a, b and c) opens the New/Editing dialog box. (See "[New/ Editing] Dialog Box
  • Canon 1321B002AB | User Manual - Page 128
    Chapter 8 Job Registration Tool Settings [New/Editing] Dialog Box The [New/Editing] dialog box appears when you click a Job button in the Job Registration Tool dialog box. The [New/Editing] dialog box appears as follows depending on the function settings registered to the Job buttons. Save as file
  • Canon 1321B002AB | User Manual - Page 129
    scanner settings. ☞ Refer to Chapter 7, "ISIS/TWAIN Driver Settings" for scanner setting procedures. Settings to Save Image Files (Functions: Save as file and Attach to E-mail) [Save Image images. [Save to My Pictures folder] Check Box Saves image files to My Pictures in the My Documents folder
  • Canon 1321B002AB | User Manual - Page 130
    or change the scanner setting. [Setting] Button This button is enabled to display the corresponding setting dialog box when the [TIFF] or [PDF] file format is selected. TIFF Settings Dialog Box [Multi-tiff setting] Select the method for saving image files when scanning multi-page documents. • Select
  • Canon 1321B002AB | User Manual - Page 131
    Box Select this check box to enable recognition of the text within images and to save the recognized text data with the image. ☞ Characters within document images are recognized as text and saved as appended text data in PDF (*pdf) files. [Access setting] Button This button is enabled when the [Save
  • Canon 1321B002AB | User Manual - Page 132
    settings. [Print format] Select whether to resize images for printing. • Select [Actual size] to print images the same size as their original documents. • Select [Fit to paper] if the scanned documents were larger than the printer paper, to resize the images to the printer paper size. Buttons [OK
  • Canon 1321B002AB | User Manual - Page 133
    the specified limit. ☞ If a warning message appears, follow the instructions in the message to either continue scanning or change the save destination ] Specify the maximum image file size that can be attached when [Attach to E-mail] is selected. When the scanned image size reaches the specified
  • Canon 1321B002AB | User Manual - Page 134
    Chapter 8 Job Registration Tool Settings [Back Up / Restore] Settings [Back Up] Button Writes a backup file (*.reg) of registered job data to the specified folder. [Restore] Button Restores the job data from a stored backup file (*.reg.) ☞ If the currently registered job number is the same as that
  • Canon 1321B002AB | User Manual - Page 135
    DR-4010C ISIS/TWAIN driver. Refer to these examples when making ISIS/TWAIN driver settings. For descriptions of particular setting items, see "ISIS/TWAIN Driver sheet, black regions may appear around the scanned document image. To scan non-standard-size documents, select [Auto-detection] as the [Page
  • Canon 1321B002AB | User Manual - Page 136
    Preferences," on p. 7-5.) Adjusting the Scan Area • To scan only part of the document page. You can specify any area on the page in the Scan the TWAIN driver, load a document in the scanner and click the [Preview] button to scan one page.) The scanned image is displayed in the Area window so that
  • Canon 1321B002AB | User Manual - Page 137
    is selected as the [Feeding Option], the scanner detects documents and starts scanning as they are loaded, so continuous document guides or sort the pages before pressing the Start button to start scanning. • To create separate files for each batch of documents during continuous scanning (ISIS driver
  • Canon 1321B002AB | User Manual - Page 138
    button to scan after loading each page. • To stop the scanner when pages double feed Confirm that the [Double Feed Detection] method selected on the [Others] tab sheet suits the document being scanned. (See "Double Feed Detection," on p. 7-21.) Image Adjustments for Scanning • To enhance text in
  • Canon 1321B002AB | User Manual - Page 139
    is disabled. • To reverse black and white in scanned images (TWAIN driver only) Select [Reverse Image] on the [Image processing] tab sheet. Black and white are reversed in scanned images. (See "[Reverse Image] Check Box (TWAIN driver only)," on p. 7-18.) • To ignore a particular color when scanning
  • Canon 1321B002AB | User Manual - Page 140
    ]," on p. 7-17.) • To Prevent Bleed Through of text from the back side of thin document pages, or to remove the background from scanned images Select [Prevent Bleed Through / Remove Background] on the [Image processing] tab sheet. Bleed-through on thin paper and backgrounds are removed from scanned
  • Canon 1321B002AB | User Manual - Page 141
    is prescanned and displayed in the Prescan panel. • About the Prescan Panel The Prescan window provides adjustments for image brightness and contrast of the first document page before continuing scanning. The image displayed in the prescan panel can be magnified for confirmation (with the mouse over
  • Canon 1321B002AB | User Manual - Page 142
    INC. 1248, SHIMOKAGEMORI, CHICHIBU-SHI, SAITAMA 369-1892, JAPAN CANON U.S.A. INC. ONE CANON PLAZA, LAKE SUCCESS, N.Y. 11042, U.S.A. CANON CANADA INC. 6390 DIXIE ROAD, MISSISSAUGA, ONTARIO L5T 1P7, CANADA CANON EUROPA N.V. BOVENKERKERWEG 59-61, P.O.BOX 2262, 1180 EG AMSTELVEEN, THE NETHERLANDS
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Document Scanner
User Manual
Please read this manual before operating this scanner.
After you finish reading this manual, store it in a safe
place for future reference.