Compaq ProLiant CL380 Compaq ProLiant CL380 User Guide - Page 109

Installing a Hot-Plug Ultra2 or Ultra3 Hard Drive, Open front bezel doors tower model only.

Get Compaq ProLiant CL380 PDF manuals and user guides View all Compaq ProLiant CL380 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 109 highlights

4-22 Compaq ProLiant CL380 User Guide Installing a Hot-Plug Ultra2 or Ultra3 Hard Drive CAUTION: One hard drive in each server node is the boot drive for that node. Removing the boot drive while it is operating normally will cause the node to fail over. NOTE: When combining Ultra2 and Ultra3 hard drives, all of the drives are limited to response times no faster than the maximum burst rate of up to 80 MB/s on the Ultra2 SCSI bus, or the transfer rate of the slowest device in the array. 1. Open front bezel doors (tower model only). 2. Remove the hard drive blanking panel from the hot-plug hard drive cage. 3. Insert the hot-plug drive . 4. Close the ejector lever . 1 2 Figure 4-23. Installing a hot plug Ultra2 or Ultra3 hard drive 5. Close front bezel doors (tower model only). NOTE: To ensure that the drive is properly latched, pull on the drive after closing the lever. If the drive is not secured in the bay, open the ejector lever and reseat the drive.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
4-22
Compaq ProLiant CL380 User Guide
Installing a Hot-Plug Ultra2 or Ultra3 Hard Drive
CAUTION:
One hard drive in each server node is the boot drive for that node.
Removing the boot drive while it is operating normally will cause the node to fail
over.
NOTE:
When combining Ultra2 and Ultra3 hard drives, all of the drives are limited to
response times no faster than the maximum burst rate of up to 80 MB/s on the Ultra2
SCSI bus, or the transfer rate of the slowest device in the array.
1.
Open front bezel doors (tower model only).
2.
Remove the hard drive blanking panel from the hot-plug hard drive
cage.
3.
Insert the hot-plug drive
.
4.
Close the ejector lever
.
1
2
Figure 4-23.
Installing a hot plug Ultra2 or Ultra3 hard drive
5.
Close front bezel doors (tower model only).
NOTE:
To ensure that the drive is properly latched, pull on the drive after closing the
lever. If the drive is not secured in the bay, open the ejector lever and reseat the drive.