D-Link DES 6000 Product Manual - Page 56

Con MAC Address Filtering, Con Static Multicast Filtering,

Get D-Link DES 6000 - Switch PDF manuals and user guides
UPC - 790069239328
View all D-Link DES 6000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Modular Ethernet Switch User's Guide Configure MAC Address Filtering The Static Filtering Table contains filtering information configured into the Switch by (local or network) management specifying MAC addresses which are not allowed to be forwarded. The Switch will check both the destination and source MAC addresses on all packets. To access the Static Filtering Table, select Configure Filtering and Forwarding Table from the System Configuration menu. Then select Configure MAC Address Filtering from the bottom of the Configure Filtering and Forwarding table screen. The following screen appears: Figure 6-24. Static Filtering Table screen To make a change to the Static Filtering Table, choose Add or Remove in the Action field. Then enter the MAC Address and VID (if Port-based or 802.1Q VLANs are enabled) and then press APPLY. Configure Static Multicast Filtering Multicast filtering allows you to block or forward traffic over each port for one multicast group. To access the Static Multicast Filtering Configuration screen, select Configure Filtering and Forwarding Table from the System Configuration menu. Then select Configure Static Multicast Filtering from the bottom of the Configure Filtering and Forwarding table screen. The following screen appears: Figure 6-25. Static Multicast Filtering Configuration screen Using the Console Interface 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
Modular Ethernet Switch User’s Guide
Using the Console Interface
51
Configure MAC Address Filtering
The Static Filtering Table contains filtering information configured into the Switch by (local or network)
management specifying MAC addresses which are not allowed to be forwarded. The Switch will check both
the destination and source MAC addresses on all packets.
To access the Static Filtering Table, select
Configure Filtering and Forwarding Table
from the
System
Configuration
menu. Then select
Configure MAC Address Filtering
from the bottom of the
Configure
Filtering and Forwarding table
screen. The following screen appears:
Figure 6-24.
Static Filtering Table screen
To make a change to the
Static Filtering Table
, choose
Add
or
Remove
in the
Action
field. Then enter the
MAC
Address
and
VID
(if Port-based or 802.1Q VLANs are enabled) and then press APPLY.
Configure Static Multicast Filtering
Multicast filtering
allows you to block or forward traffic over each port for one multicast group.
To access the
Static Multicast Filtering Configuration
screen, select
Configure Filtering and
Forwarding Table
from the
System Configuration
menu. Then select
Configure Static Multicast
Filtering
from the bottom of the
Configure Filtering and Forwarding table
screen. The following screen
appears:
Figure 6-25.
Static Multicast Filtering Configuration screen