Dell Inspiron 530 Owner's Manual - Page 141

reflect these changes in system setup. When you restart your computer

Page 141 highlights

1 5 2 3 4 1 hard drive 2 power cable 4 system board connector 5 screws (4) 3 serial ATA data cable NOTE: The location of connectors on the system board may vary depending on your computer.See "Inside View of Your Computer" on page 109. 5 Remove the four screws securing the hard drive. NOTICE: Ensure that you do not scratch the screw holes with the screw driver as the hard disk circuit board assembly is exposed here. 6 Slide the drive out away from the front of the computer. 7 If removing this drive changes the drive configuration, then be sure to reflect these changes in system setup. When you restart your computer, enter system setup (see "System Setup" on page 187), then go to the "Drives" section of the System Setup and under Drive 0 through 3, set the Drive to the correct configuration. Removing and Installing Parts 141

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226

Removing and Installing Parts
141
NOTE:
The location of connectors on the system board may vary depending on
your computer.See "Inside View of Your Computer" on page 109.
5
Remove the four screws securing the hard drive.
NOTICE:
Ensure that you do not scratch the screw holes with the screw driver as
the hard disk circuit board assembly is exposed here.
6
Slide the drive out away from the front of the computer.
7
If removing this drive changes the drive configuration, then be sure to
reflect these changes in system setup. When you restart your computer,
enter system setup (see "System Setup" on page 187), then go to the
"Drives" section of the System Setup and under
Drive 0 through 3
, set the
Drive to the correct configuration.
1
hard drive
2
power cable
3
serial ATA data cable
4
system board connector
5
screws (4)
2
4
3
1
5