Denon AVR 2807 Owners Manual - English - Page 16

Checking and storing the measurement, results, Error messages - reset

Get Denon AVR 2807 - AV Receiver PDF manuals and user guides
UPC - 081757507059
View all Denon AVR 2807 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Easy Setup Procedure i Checking and storing the measurement results The measurement results displayed at "u Speaker measurements" can be checked and stored in the memory. Easy Setup Procedure Error messages An error message is displayed if the measurements could not be completed automatically due to the speaker layout, the measuring environment, etc. Please check the following matters, reset the pertinent items, and measure again. Be sure to turn off the AVR-2807's power before checking the speaker connections. 1 Press D H to select the item, then press ENTER. Press ENTER to switch to the second screen. 2 After checking, press ENTER, then press D H to set. Example Cause Measures q The speakers required for producing suitable • Check that the pertinent speakers are properly reproduction have not been detected. connected. If multiple errors occur, press F G to check the contents. Store: All the settings are stored in the memory. Cancel: Cancel the auto setup settings. 3 When "Store" is selected: Press F. • After the data is stored, the "Auto Setup / Room EQ" screen appears automatically. 1 w The speaker polarity is connected in reverse. • Check the polarity of the pertinent speakers. • For some speakers, the screen below may be If multiple errors occur, press F G to check the displayed even though the speakers are contents. properly connected. If so, select "Skip0". e There is too much ambient noise in the room and the • Either turn off the power of the device that measurements cannot be made accurately. generated the noise during the measurements or move the device away. • Try again at a time when it is quieter. r The sound level that is output from the speakers and/or • Check the placement and orientation of the subwoofer is too low. loudspeakers. • Adjust the subwoofer's output level. 2 t The measurement microphone is not connected, or all • Connect the attached setup microphone to of speakers have not been detected. . • Check the speaker connection. • When measurements have been made using the measurement microphone, speakers with a built-in filter such as subwoofers might be set with a value that differs from the physical distance because of the internal electrical delay. NOTE: • Do not turn off the power while the data is being stored. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Measures
Cause
Example
12
Easy Setup Procedure
Easy Setup Procedure
i
Checking and storing the measurement
results
Press
DH
to select the item, then press
ENTER
.
Press
ENTER
to switch to the second screen.
The measurement results displayed at “
u
Speaker measurements”
can be checked and stored in the memory.
1
Store:
All the settings are stored in the memory.
After checking, press
ENTER
, then press
DH
to
set.
When “Store” is selected:
Press
F
.
• After the data is stored, the “Auto Setup / Room EQ”
screen appears automatically.
Cancel:
Cancel the auto setup settings.
• When measurements have been made using the measurement
microphone, speakers with a built-in filter such as subwoofers
might be set with a value that differs from the physical distance
because of the internal electrical delay.
NOTE:
• Do not turn off the power while the data is being stored.
2
3
1
2
q
The
speakers
required
for
producing
suitable
reproduction have not been detected.
If multiple errors occur, press
F
G
to check the
contents.
• Check that the pertinent speakers are properly
connected.
w
The speaker polarity is connected in reverse.
If multiple errors occur, press
F
G
to check the
contents.
• Check the polarity of the pertinent speakers.
• For some speakers, the screen below may be
displayed even though the speakers are
properly connected.
If so, select “Skip
0
”.
e
There is too much ambient noise in the room and the
measurements cannot be made accurately.
r
The sound level that is output from the speakers and/or
subwoofer is too low.
• Either turn off the power of the device that
generated the noise during the measurements
or move the device away.
• Try again at a time when it is quieter.
• Check the placement and orientation of the
loudspeakers.
• Adjust the subwoofer’s output level.
t
The measurement microphone is not connected, or all
of speakers have not been detected.
• Connect the attached setup microphone to
<
SETUP MIC
>
.
• Check the speaker connection.
Error messages
An error message is displayed if the measurements could not be completed automatically due to the speaker layout, the measuring
environment, etc. Please check the following matters, reset the pertinent items, and measure again.
Be sure to turn off the AVR-2807’s power before checking the speaker connections.