Denon AVR-3311CI Owners Manual - English - Page 84

Simple version Basic version Setting items Distance (Continued) Setting details • The speakers that can be selected differ depending on the "Amp Assign" (vpage 79) and "Speaker Config." (vpage 79) settings. • Default settings : Front L / Front R / Center / Subwoofer / F.Height L / F.Height R / F.Wide L / F.Wide R : 12.0 ft (3.6 m) Surround L / Surround R / S.Back L / S.Back R : 10.0 ft (3.0 m) • Set the difference in the distance between the speakers to less than 20 ft (6.0 m). NOTE Speakers set to "None" in "Speaker Config." (vpage 79) are not displayed. Default : The "Distance" settings are returned to the default settings. • Yes : Reset to the defaults. • No : Do not reset to the defaults. When you select "Default" and press ENTER, the "Default Setting?" prompt is displayed. Select either "Yes" or "No", and press ENTER. Channel Level Test Tone Start : Output test tone. Set the volume of the test • Front L / F.Height L / Center / F.Height R / Front R / F.Wide R / tone to be the same when it Surround R / S.Back Rz / S.Back Lz / Surround L / F.Wide L / is output from each speaker. Subwoofer : Select the speaker. zz When the "Speaker Config." - "S.Back" setting (vpage 80) is set to "1spkr", "S.Back" is displayed. • -12.0dB - +12.0dB (0.0dB) : Adjust the volume. • When o is pressed while the subwoofer volume is set to "-12 dB", the "Subwoofer" setting switches to "OFF". • When "Channel Level" is adjusted, the adjusted values are set for all the surround modes. To adjust the channel level separately for the different surround modes, use the operation see page 55. NOTE • Speakers set to "None" in the "Speaker Config." (vpage 79) settings are not displayed. • When a headphones jack is inserted in the PHONES jack of this unit, the "Channel Level" is not displayed. Default : The "Channel Level" settings are returned to the default settings. • Yes : Reset to the defaults. • No : Do not reset to the defaults. When you select "Default" and press ENTER, the "Default Setting?" prompt is displayed. Select either "Yes" or "No", and press ENTER. ENGLISH Manual Setup Setting items Setting details Crossover Frequency Crossover : Set the crossover frequency. Set the maximum frequency • 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / of the bass signal output 250Hz from each channel to the subwoofer. Set the Crossover Frequency to suit the bass reproduction capability of the speaker being used. Advanced : Specify crossover frequency for each speaker. • Front / Center / Surround / S.Back / F.Height / F.Wide : Select the speaker. • 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz : Set the crossover frequency. Front Speaker Setup Set the front speakers to use for every surround mode. NOTE This can be set when "Amp Assign" is set to "Front B" (vpage 79). • "Crossover Frequency" can be set when the "Bass Setting" - "Subwoofer Mode" (vpage 80) setting is "LFE+Main", or when you have a speaker that is set to "Small". • Always set the crossover frequency to "80Hz". When using small speakers, however, we recommend setting the crossover frequency to a higher frequency. • For speakers set to "Small", sound below the crossover frequency is cut from the sound output. The cut bass sound is output from the subwoofer or front speakers. • The speakers that can be set when "Advanced" is selected differ depending on to the "Subwoofer Mode" setting (vpage 80). • When "LFE" is selected, speakers set to "Small" at "Speaker Config." can be set. If the speakers are set to "Large", "Full Band" is displayed and the setting cannot be made. • If set to "LFE+Main", this setting can be made regardless of the speaker size. 2CH DIRECT/STEREO : The front speakers used in the direct, stereo and pure direct play modes (2 channel) are set in advance. • A : Front speaker A is used. • B : Front speaker B is used. • A+B : Both front speakers A and B are used. MULTI CH : The front speakers used in modes other than the direct, stereo and pure direct play modes (2 channel) are set in advance. • A : Front speaker A is used. • B : Front speaker B is used. • A+B : Both front speakers A and B are used. Advanced version Information Remote control operation buttons Move the cursor (Up/Down/Left/Right) Confirm the setting Return to previous menu 81