Gateway 9315 Gateway 9315 Server User Guide - Page 50

Installing and removing drives, Installing a diskette in a converted hard drive bay

Get Gateway 9315 PDF manuals and user guides View all Gateway 9315 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Installing and removing drives Your server's basic configuration includes one CD or DVD drive and as many as three SATA fixed hard drives. SATA hot-swap hard drives and a hot-swap backplane are optional. A USB diskette drive is also included (but not installed in the server). As you prepare to install drives, remember: ■ You must install a diskette drive in the left converted hard drive bay. ■ Before you install a drive, see the drive's documentation for information on configuring the drive, setting drive jumpers, and attaching cables. ■ You may need to configure the drives you install using the BIOS Setup utility. Press F2 at startup to open the BIOS Setup utility. Installing a diskette in a converted hard drive bay If you need to install a diskette drive into your server, you must install the diskette drive in one of the hard drive bays. Important An internal diskette drive can only be installed in a converted hard drive bay if the optional hot-swap backplane is installed in your server. To install a diskette drive in a converted hard drive bay: 1 Follow the instructions in "Preventing static electricity discharge" on page 37. Make sure that you turn off the server, then unplug the power cord and all other cables connected to the server. Caution The diskette drive is not hot-swappable. Before installing or removing the drive, make sure that power is turned off and the power cord is unplugged. 2 Follow the instructions in "Opening the server case" on page 38. 3 Unlock the bezel (if necessary) and remove it by pulling it from the chassis. 4 Remove the left hot-swap hard drive carrier from the server. www.gateway.com 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
45
www.gateway.com
Installing and removing drives
Your server’s basic configuration includes one CD or DVD drive and as many as three SATA
fixed hard drives. SATA hot-swap hard drives and a hot-swap backplane are optional. A
USB diskette drive is also included (but not installed in the server).
As you prepare to install drives, remember:
■
You must install a diskette drive in the left converted hard drive bay.
■
Before you install a drive, see the drive’s documentation for information on
configuring the drive, setting drive jumpers, and attaching cables.
■
You may need to configure the drives you install using the BIOS Setup utility. Press
F2
at startup to open the BIOS Setup utility.
Installing a diskette in a converted hard drive bay
If you need to install a diskette drive into your server, you must install the diskette drive
in one of the hard drive bays.
To install a diskette drive in a converted hard drive bay:
1
Follow the instructions in
“Preventing static electricity discharge” on page 37
. Make
sure that you turn off the server, then unplug the power cord and all other cables
connected to the server.
2
Follow the instructions in
“Opening the server case” on page 38
.
3
Unlock the bezel (if necessary) and remove it by pulling it from the chassis.
4
Remove the left hot-swap hard drive carrier from the server.
Important
An internal diskette drive can only be installed in a converted hard
drive bay if the optional hot-swap backplane is installed in your server.
Caution
The diskette drive is not hot-swappable. Before installing or removing
the drive, make sure that power is turned off and the power cord is
unplugged.