Gateway 9315 Gateway 9315 Server User Guide - Page 55

Installing a CD or DVD drive

Get Gateway 9315 PDF manuals and user guides View all Gateway 9315 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Installing a CD or DVD drive To install a CD or DVD drive: 1 Follow the instructions in "Preventing static electricity discharge" on page 37. Make sure that you turn off the server, then unplug the power cord and all other cables connected to the server. Caution The CD or DVD drive is not hot-swappable. Before installing or removing the drive, make sure that power is turned off and the power cord is unplugged. 2 Follow the instructions in "Opening the server case" on page 38. 3 Unlock the bezel (if necessary) and remove it by pulling it from the chassis. 4 Remove the slim-line drive bay filler panel. - OR - Remove the CD/DVD drive carrier by pressing the blue lever at the back of the carrier and pushing the carrier out the front of the server. 5 Place the CD or DVD drive in the drive carrier (included with your server) by aligning the two holes in the left side of the drive with the two alignment pins in the carrier, then lowering the right side of the drive into the carrier until it clicks into place. Screws Interposer board CD or DVD drive Drive carrier 50 www.gateway.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
50
www.gateway.com
Installing a CD or DVD drive
To install a CD or DVD drive:
1
Follow the instructions in
“Preventing static electricity discharge” on page 37
. Make
sure that you turn off the server, then unplug the power cord and all other cables
connected to the server.
2
Follow the instructions in
“Opening the server case” on page 38
.
3
Unlock the bezel (if necessary) and remove it by pulling it from the chassis.
4
Remove the slim-line drive bay filler panel.
- OR -
Remove the CD/DVD drive carrier by pressing the blue lever at the back of the carrier
and pushing the carrier out the front of the server.
5
Place the CD or DVD drive in the drive carrier (included with your server) by aligning
the two holes in the left side of the drive with the two alignment pins in the carrier,
then lowering the right side of the drive into the carrier until it clicks into place.
Caution
The CD or DVD drive is not hot-swappable. Before installing or
removing the drive, make sure that power is turned off and the power
cord is unplugged.
Interposer board
CD or DVD drive
Screws
Drive carrier