GE 60-806-95R-16Z Installation Instructions - Page 16

Connecting 4-Wire Smoke Detectors

Get GE 60-806-95R-16Z - Security Concord Express System Control Panel PDF manuals and user guides
UPC - 046188090938
View all GE 60-806-95R-16Z manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

ZC O M / Z6/ 2W - 2W + Panel Terminals 1 6 17 - + - + Note The Two-Wire Smoke setting (in program mode) must be off when connecting 4-wire smoke detectors to zone 6. For UL Listed systems, 4-wire smoke detectors cannot be connected to onboard panel zone inputs. 2k Ohm EOL Resistor (49-454) Locate at Last Device Figure 10. Connecting 2-Wire Smoke Detectors Connecting 4-Wire Smoke Detectors Zone inputs 1 through 6 can be used with 4-wire smoke detectors that latch and remain in the alarm state until power is removed and then restored to the detector. The panel provides this power interruption from panel terminal 8 (OUT2/OC) provided that the output configuration number is set (in program mode) to 01500. For more information on output configuration numbers, see the section "Programming the Panel" and the tables in Appendix A. Use only 4-wire smoke detectors that operate on 8.5 to 14.2 VDC. Connect up to five Sentrol (ESL) model 449AT (ITI part no. 13-360) smoke detectors to panel power input as shown in Figure 11. 11 Installing the System

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Installing the System
11
Figure 10.
Connecting 2-Wire Smoke Detectors
Connecting 4-Wire Smoke Detectors
Zone inputs 1 through 6 can be used with 4-wire smoke detectors that latch and remain in the
alarm state until power is removed and then restored to the detector.
The panel provides this power interruption from panel terminal 8 (OUT2/OC) provided that the
output configuration number is set (in program mode) to 01500.
For more information on output configuration numbers, see the section “Programming the Panel”
and the tables in Appendix A. Use only 4-wire smoke detectors that operate on 8.5 to 14.2 VDC.
Note
The Two-Wire Smoke set-
ting (in program mode) must
be off when connecting
4-wire smoke detectors to
zone 6.
For UL Listed systems,
4-wire smoke detectors can-
not be connected to onboard
panel zone inputs.
Connect up to five Sentrol (ESL) model 449AT (ITI part no. 13-360) smoke detectors to panel
power input as shown in Figure 11.
16
17
ZC
O
M
/
2W
-
Z6/
2W
+
+
-
+
-
2k Ohm
EOL Resistor
(49-454)
Locate at
Last Device
Panel
Terminals