HP StorageWorks 8/80 EZSwitchSetup Administrator's Guide v6.3.0 (53-1001344-01 - Page 17

Setting Up Your Switch, In this Installing and running the EZSwitchSetup wizard

Get HP StorageWorks 8/80 - SAN Switch PDF manuals and user guides View all HP StorageWorks 8/80 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Setting Up Your Switch Chapter 2 In this chapter •Installing and running the EZSwitchSetup wizard 5 •Configuring the switch 16 •Zoning selection options 17 •Connecting devices and completing the setup 19 Installing and running the EZSwitchSetup wizard You can run EZSwitchSetup from a computer you are currently using for SAN administration, or you can use a different computer that is not part of the SAN, such as a laptop. In this chapter, the computer running EZSwitchSetup is called the setup computer. The first step in setting up your switch is to install the EZSwitchSetup wizard, which is located on the EZSwitchSetup installation CD. 1. Insert the EZSwitchSetup CD into the CD-ROM drive of your setup computer. • On Windows: The installer will autostart in about a minute. • On Linux: Navigate to the following path location on the CD-ROM: /CDROM_Installers/Linux/Disk1/InstData/VM/install.bin 2. Install EZSwitchSetup following the onscreen directions. Installation will take a few minutes after you click OK. 3. Click Done on the last screen (shown in Figure 3) to exit the installer. EZSwitchSetup Administrator's Guide 5 53-1001344-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
EZSwitchSetup Administrator’s Guide
5
53-1001344-01
Chapter
2
Setting Up Your Switch
In this chapter
•
Installing and running the EZSwitchSetup wizard. . . . . . . . . . . . . . . . . . . . . .
5
•
Configuring the switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
•
Zoning selection options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
•
Connecting devices and completing the setup . . . . . . . . . . . . . . . . . . . . . . .
19
Installing and running the EZSwitchSetup wizard
You can run EZSwitchSetup from a computer you are currently using for SAN administration, or you
can use a different computer that is not part of the SAN, such as a laptop. In this chapter, the
computer running EZSwitchSetup is called the setup computer.
The first step in setting up your switch is to install the EZSwitchSetup wizard, which is located on
the EZSwitchSetup installation CD.
1.
Insert the EZSwitchSetup CD into the CD-ROM drive of your setup computer.
•
On Windows:
The installer will autostart in about a minute.
•
On Linux:
Navigate to the following path location on the CD-ROM:
<CD-ROM Path>
/CDROM_Installers/Linux/Disk1/InstData/VM/install.bin
2.
Install EZSwitchSetup following the onscreen directions.
Installation will take a few minutes after you click
OK
.
3.
Click
Done
on the last screen (shown in
Figure 3
) to exit the installer.