HP rp5400 Installation Guide, Third Edition - HP rp5400 Family of Servers - Page 13

Step 6., the two captive screws to secure the top cover in place.

Get HP rp5400 PDF manuals and user guides View all HP rp5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Step 6. Refer to the following graphic for memory slot locations. Installing Additional Components Installing Memory Locate the correct DIMM pair slots. Insert the DIMM connectors into the guides until the card snaps firmly in place. It may be necessary to apply downward force using the palm of your hand on the DIMM. Observe the top of the DIMM to make sure one side is not higher than the other. NOTE It may be necessary to remove PSM 1 when installing a DIMM in slot 0a and PSM 0 when installing a DIMM in slot 1b. If either PSM is removed to install memory, ensure it is re-installed. Step 7. Replace the air baffle. Tighten the four captive screws to secure the air baffle in place. Step 8. Replace the top cover. Slide the cover tabs into the slots in the chassis and close the cover. Tighten the two captive screws to secure the top cover in place. Step 9. For rack configurations, insert the rp54xx Server back into the rack. Step 10. For deskside enclosure configurations, replace the deskside enclosure cover. Step 11. Power the rp54xx Server on. Step 12. Use the BCH command in me to verify the system recognizes the memory that you have just added. Chapter 1 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Installing Additional Components
Installing Memory
Chapter 1
13
Step 6.
Refer to the following graphic for memory slot locations.
Locate the correct DIMM pair slots. Insert the DIMM connectors into the guides until the card
snaps firmly in place. It may be necessary to apply downward force using the palm of your hand on
the DIMM. Observe the top of the DIMM to make sure one side is not higher than the other.
NOTE
It may be necessary to remove PSM 1 when installing a DIMM in slot 0a and PSM 0
when installing a DIMM in slot 1b. If either PSM is removed to install memory,
ensure it is re-installed.
Step 7.
Replace the air baffle. Tighten the four captive screws to secure the air baffle in place.
Step 8.
Replace the top cover. Slide the cover tabs into the slots in the chassis and close the cover. Tighten
the two captive screws to secure the top cover in place.
Step 9.
For rack configurations, insert the rp54xx Server back into the rack.
Step 10.
For deskside enclosure configurations, replace the deskside enclosure cover.
Step 11.
Power the rp54xx Server on.
Step 12.
Use the BCH command
in me
to verify the system recognizes the memory that you have just
added.