HP rp5400 Installation Guide, Third Edition - HP rp5400 Family of Servers - Page 46

Step 10., Pins in Slots

Get HP rp5400 PDF manuals and user guides View all HP rp5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Server Unpacking and Installation Install Stand-Alone Server in a Cabinet Step 10. Use an M5 x 30 screw with a cress cup washer to attach the front of the slide to the vertical mounting post. Insert the screw through the slide, through the center hole of the aluminum spacer, through the vertical mounting post, and tighten into the sheet metal nut located at that position. Step 11. Use a procedure similar to steps 7 through 10 to install the right hand slide/bracket assembly (marked 337079-1R) and then proceed to step 12. Step 12. Take the tray and place it onto the pins that extend from the slides' inner members. The slots with wide lead-in guides on the side of the tray fit down onto the slides' pins. The flat part of the tray will be on top, and the mounting holes in the top of the tray will be located to the right of the center of the tray. Slide the tray all the way down on both sides so that the pins reach the top of the slots in the side of the tray. Pins in Slots 46 Chapter 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Server Unpacking and Installation
Install Stand-Alone Server in a Cabinet
Chapter 2
46
Step 10.
Use an M5 x 30 screw with a cress cup washer to attach the front of the slide to the vertical
mounting post. Insert the screw through the slide, through the center hole of the aluminum spacer,
through the vertical mounting post, and tighten into the sheet metal nut located at that position.
Step 11.
Use a procedure similar to steps 7 through 10 to install the right hand slide/bracket assembly
(marked 337079-1R) and then proceed to step 12.
Step 12.
Take the tray and place it onto the pins that extend from the slides' inner members. The slots with
wide lead-in guides on the side of the tray fit down onto the slides' pins. The flat part of the tray will
be on top, and the mounting holes in the top of the tray will be located to the right of the center of
the tray. Slide the tray all the way down on both sides so that the pins reach the top of the slots in
the side of the tray.
Pins in Slots