HP rp5400 Installation Guide, Third Edition - HP rp5400 Family of Servers - Page 44

Step 3., into the appropriate vertical, rectangular slot on the front

Get HP rp5400 PDF manuals and user guides View all HP rp5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Server Unpacking and Installation Install Stand-Alone Server in a Cabinet Step 3. On the front vertical mounting posts only, slide M5 sheet metal nuts onto the posts over the holes immediately adjacent to the vertical slots determined in the previous step. Also place M5 sheet metal nuts on the holes directly above these. Orient the sheet metal nuts so that the threaded portion faces towards the outside of the cabinet. There should now be a total of four (4) sheet metal nuts installed. Step 4. If the cabinet is a non-E-Series cabinet, discard the left hand and right hand aluminum spacers and two of the M5 x 16 screws with cress-cup washers and proceed to step 12. Step 5. If the cabinet is an E-Series cabinet, place the hook of the aluminum spacer marked "L" (5183-1864) into the appropriate vertical, rectangular slot on the front, left hand mounting post. The hook points downward. Similarly, place the spacer marked "R" (5183-1863) into the appropriate slot on the right hand mounting post. Step 6. Use one M5 x 16 screw with cress-cup washer to attach each spacer to its vertical post. Do this by inserting the screw through the top hole in the spacer, through the mounting rail and tightening it into the sheet metal nut located at that position. 44 Chapter 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Server Unpacking and Installation
Install Stand-Alone Server in a Cabinet
Chapter 2
44
Step 3.
On the front vertical mounting posts
only
, slide M5 sheet metal nuts onto the posts over the holes
immediately adjacent to the vertical slots determined in the previous step. Also place M5 sheet
metal nuts on the holes directly above these. Orient the sheet metal nuts so that the threaded
portion faces towards the outside of the cabinet. There should now be a total of four (4) sheet metal
nuts installed.
Step 4.
If the cabinet is a non-E-Series cabinet, discard the left hand and right hand aluminum spacers and
two of the M5 x 16 screws with cress-cup washers and proceed to step 12.
Step 5.
If the cabinet is an E-Series cabinet, place the hook of the aluminum spacer marked “L” (5183-1864)
into the appropriate vertical, rectangular slot on the front, left hand mounting post. The hook
points downward. Similarly, place the spacer marked “R” (5183-1863) into the appropriate slot on
the right hand mounting post.
Step 6.
Use one M5 x 16 screw with cress-cup washer to attach each spacer to its vertical post. Do this by
inserting the screw through the top hole in the spacer, through the mounting rail and tightening it
into the sheet metal nut located at that position.