HP rp5400 Installation Guide, Third Edition - HP rp5400 Family of Servers - Page 14

Installing rp5470 DIMMs, slots in the chassis. The air baffle will be exposed.

Get HP rp5400 PDF manuals and user guides View all HP rp5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Installing Additional Components Installing Memory Installing rp5470 DIMMs Step 1. Power down and unplug the rp54xx Server. NOTE DC voltages are present when the server is connected to AC power. Do not attempt to install or service: CPUs, memory, PSMs, the platform monitor or PCI I/O cards installed in non-turbo slots (1-6) while DC voltage is present. Failure to observe this warning may result in damage to the server. Step 2. Make the top of the server accessible for service. Step 3. Loosen the captive T-15 screws that hold the top cover in place, then grasp the strap handle, raise the cover slightly, and pull the cover toward the front of the server to free the cover tabs from the slots in the chassis. The air baffle will be exposed. Step 4. Loosen the four (4) captive T-15 screws on the air baffle. Grasp the two handles on the baffle, and lift and remove the baffle. Step 5. Observe electrostatic discharge (ESD) precautions. Step 6. Refer to the following graphic for memory carrier locations. 14 Chapter 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Installing Additional Components
Installing Memory
Chapter 1
14
Installing rp5470 DIMMs
Step 1.
Power down and unplug the rp54xx Server.
NOTE
DC voltages are present when the server is connected to AC power. Do not attempt to
install or service: CPUs, memory, PSMs, the platform monitor or PCI I/O cards
installed in non-turbo slots (1-6) while DC voltage is present. Failure to observe this
warning may result in damage to the server.
Step 2.
Make the top of the server accessible for service.
Step 3.
Loosen the captive T-15 screws that hold the top cover in place, then grasp the strap handle, raise
the cover slightly, and pull the cover toward the front of the server to free the cover tabs from the
slots in the chassis. The air baffle will be exposed.
Step 4.
Loosen the four (4) captive T-15 screws on the air baffle. Grasp the two handles on the baffle, and
lift and remove the baffle.
Step 5.
Observe electrostatic discharge (ESD) precautions.
Step 6.
Refer to the following graphic for memory carrier locations.