HP rp5400 Installation Guide, Third Edition - HP rp5400 Family of Servers - Page 20

Installing a PCI Card, Step 1., rp5400, rp5430/rp5470, Slot Type, Turbo, Twin Turbo

Get HP rp5400 PDF manuals and user guides View all HP rp5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Installing Additional Components Installing Peripheral Component Interconnect (PCI) Cards Installing a PCI Card Follow these procedures to install a PCI card. Step 1. Power down and unplug the rp54xx Server. NOTE DC voltages are present when the server is connected to AC power. Do not attempt to install or service: CPUs, memory, PSMs, the platform monitor or PCI I/O cards installed in non-turbo slots (1-6) while DC voltage is present. Failure to observe this warning may result in damage to the server. Step 2. Make the right side of the server accessible for service. Step 3. Using a torx 15 screwdriver, loosen the captive screws on the right side panel. This panel has a label which shows which PCI I/O slots are available and the corresponding paths. The PCI I/O slot paths for rp5400, rp5450, and rp5470 are shown below. Slot rp5400 Slot Type Path rp5450 Slot/Type Path rp5430/rp5470 Slot Type Path 12 Turbo 0/4/0 Turbo 0/4/0 Twin Turbo 11 Turbo 0/7/0 Turbo 0/7/0 Twin Turbo 10 Turbo 0/3/0 Turbo 0/3/0 Turbo 9 Turbo 0/6/0 Turbo 0/6/0 Turbo 8 Turbo 0/2/0 Turbo 0/2/0 Turbo 7 Not Available Turbo 0/5/0 Turbo1 6 Not Available Shared 0/1/0 Turbo1 5 Not Available Shared 0/1/1 Turbo1 4 Not Available Shared 0/1/2 Shared1 3 Not Available2 Shared 0/1/3 Shared 2 GSP GSP GSP 1 LAN/SCSI LAN/SCSI LAN/SCSI 1. Slot is NOT AVAILABLE for rp5430. 2. Slot 3 becomes available with server firmware versions later than 40.48. 0/10/0 0/12/0 0/8/0 0/9/0 0/3/0 0/1/0 0/5/0 0/2/0 0/4/0 0/4/2 20 Chapter 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Installing Additional Components
Installing Peripheral Component Interconnect (PCI) Cards
Chapter 1
20
Installing a PCI Card
Follow these procedures to install a PCI card.
Step 1.
Power down and unplug the rp54xx Server.
NOTE
DC voltages are present when the server is connected to AC power. Do not attempt to
install or service: CPUs, memory, PSMs, the platform monitor or PCI I/O cards
installed in non-turbo slots (1-6) while DC voltage is present. Failure to observe this
warning may result in damage to the server.
Step 2.
Make the right side of the server accessible for service.
Step 3.
Using a torx 15 screwdriver, loosen the captive screws on the right side panel. This panel has a
label which shows which PCI I/O slots are available and the corresponding paths. The PCI I/O slot
paths for rp5400, rp5450, and rp5470 are shown below.
Slot
rp5400
rp5450
rp5430/rp5470
Slot Type
Path
Slot/Type
Path
Slot Type
Path
12
Turbo
0/4/0
Turbo
0/4/0
Twin Turbo
0/10/0
11
Turbo
0/7/0
Turbo
0/7/0
Twin Turbo
0/12/0
10
Turbo
0/3/0
Turbo
0/3/0
Turbo
0/8/0
9
Turbo
0/6/0
Turbo
0/6/0
Turbo
0/9/0
8
Turbo
0/2/0
Turbo
0/2/0
Turbo
0/3/0
7
Not Available
Turbo
0/5/0
Turbo
1
0/1/0
6
Not Available
Shared
0/1/0
Turbo
1
0/5/0
5
Not Available
Shared
0/1/1
Turbo
1
0/2/0
4
Not Available
Shared
0/1/2
Shared
1
1. Slot is NOT AVAILABLE for rp5430.
0/4/0
3
Not
Available
2
2. Slot 3 becomes available with server firmware versions later than 40.48.
Shared
0/1/3
Shared
0/4/2
2
GSP
GSP
GSP
1
LAN/SCSI
LAN/SCSI
LAN/SCSI