HP rp5400 Installation Guide, Third Edition - HP rp5400 Family of Servers - Page 35

Bolts, when rolling the cabinet off the pallet or injury may occur. All but the smallest

Get HP rp5400 PDF manuals and user guides View all HP rp5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Server Unpacking and Installation Factory Integrated rp54xx Cabinet Installation 3. At the rear of the cabinet: a. Open the door. b. Remove the anti-tip foot by removing and retaining the two (2) 1/2-inch bolts. Bolts For Shipping: L-brackets are mounted behind anti-tip foot. Same bolts secure both. c. Remove the two (2) L-brackets (revealed by removing the anti-tip foot). 4. Remove the two ramps from the pallet and carefully place them into the slots at the front of the pallet. WARNING Use extreme care when rolling the racked system down the ramps. A rack containing one rp54xx can weigh up to 418 lbs. Do not stand in front of the ramps when rolling the cabinet off the pallet or injury may occur. All but the smallest configurations require two persons to safely remove the rack from the pallet. If anti-tip feet or ballast are not installed or are improperly installed the cabinet can tip. Failure to follow this precaution can cause injury to personnel or damage to equipment. Chapter 2 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Server Unpacking and Installation
Factory Integrated rp54xx Cabinet Installation
Chapter 2
35
3. At the rear of the cabinet:
a.
Open the door.
b.
Remove the anti-tip foot by removing and retaining the two (2) 1/2-inch bolts.
c.
Remove the two (2) L-brackets (revealed by removing the anti-tip foot).
4. Remove the two ramps from the pallet and carefully place them into the slots at the front of the pallet.
WARNING
Use extreme care when rolling the racked system down the ramps. A rack
containing one rp54xx can weigh up to 418 lbs. Do not stand in front of the ramps
when rolling the cabinet off the pallet or injury may occur. All but the smallest
configurations require two persons to safely remove the rack from the pallet.
If anti-tip feet or ballast are not installed or are improperly installed the cabinet
can tip. Failure to follow this precaution can cause injury to personnel or damage
to equipment.
Bolts
For Shipping:
L-brackets are
mounted behind
anti-tip foot.
Same bolts
secure both.