IBM 79856au User Guide - Page 67

completing

Get IBM 79856au - Servers System X3655 Opteron 2.8ghz PDF manuals and user guides
UPC - 883436004374
View all IBM 79856au manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Microprocessor release lever Microprocessor socket dust cover b. Remove the protective dust cover, tape, or label from the surface of the microprocessor socket, if one is present. c. Rotate the microprocessor release lever on the socket from its closed and locked position until it stops or clicks in the fully open position. Attention: v Handle the microprocessor carefully. Dropping the microprocessor during installation or removal can damage the contacts. Also, contaminants on the microprocessor contacts, such as oil from your skin, can cause connection failures between the contacts and the socket. v Do not use excessive force when pressing the microprocessor into the socket d. Align the microprocessor with the socket (note the alignment mark and the position of the notches); then, carefully place the microprocessor on the socket. Close the microprocessor bracket frame. Microprocessor Alignment marks Notches Note: The microprocessor fits only one way on the socket. e. Carefully close the microprocessor release lever to secure the microprocessor in the socket. 7. Install a heat sink on the microprocessor by completing the following steps. Chapter 2. Installing optional devices 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Microprocessor
release lever
Microprocessor
socket dust cover
b.
Remove
the
protective
dust
cover,
tape,
or
label
from
the
surface
of
the
microprocessor
socket,
if
one
is
present.
c.
Rotate
the
microprocessor
release
lever
on
the
socket
from
its
closed
and
locked
position
until
it
stops
or
clicks
in
the
fully
open
position.
Attention:
v
Handle
the
microprocessor
carefully.
Dropping
the
microprocessor
during
installation
or
removal
can
damage
the
contacts.
Also,
contaminants
on
the
microprocessor
contacts,
such
as
oil
from
your
skin,
can
cause
connection
failures
between
the
contacts
and
the
socket.
v
Do
not
use
excessive
force
when
pressing
the
microprocessor
into
the
socket
d.
Align
the
microprocessor
with
the
socket
(note
the
alignment
mark
and
the
position
of
the
notches);
then,
carefully
place
the
microprocessor
on
the
socket.
Close
the
microprocessor
bracket
frame.
Microprocessor
Alignment marks
Notches
Note:
The
microprocessor
fits
only
one
way
on
the
socket.
e.
Carefully
close
the
microprocessor
release
lever
to
secure
the
microprocessor
in
the
socket.
7.
Install
a
heat
sink
on
the
microprocessor
by
completing
the
following
steps.
Chapter
2.
Installing
optional
devices
53