Lenovo A600 Lenovo IdeaCentre A600 Hardware Maintenance Manual - Page 74

Replacing the touch sensor board

Get Lenovo A600 - IdeaCentre 3011 6DU All-in-One PC PDF manuals and user guides
UPC - 884942547713
View all Lenovo A600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Hardware Maintenance Manual 8. Set the new inverter board on the bracket, aligning the two screw holes on the board to the mounting holes on the bracket. 9. Screw back the two screws on the inverter board. 10. Connect the cables to the inverter board. 11. Replace the inverter board bracket to the chassis aligning the screw hole on the metal bracket to the mounting hole on the chassis. 12. Screw back the two screws on the metal bracket. 13. Close the system bay. 14. Refer to "Completing the installation". Replacing the touch sensor board To replace the touch sensor board 1. Remove the computer cover. Refer to "Removing the computer cover". 2. Open the system bay. Refer to step 2 of the "Replacing the hard disk drive" section. 3. Remove the wireless keyboard and mouse receiver module. Refer to "Replacing the wireless keyboard and mouse receiver module". 4. Disconnect the touch sensor board cable from the system board. 72

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
Hardware Maintenance Manual
72
8.
Set the new inverter board on the bracket, aligning the two screw
holes on the board to the mounting holes on the bracket.
9. Screw back the two screws on the inverter board.
10. Connect the cables to the inverter board.
11. Replace the inverter board bracket to the chassis aligning the screw
hole on the metal bracket to the mounting hole on the chassis.
12. Screw back the two screws on the metal bracket.
13. Close the system bay.
14. Refer to “Completing the installation”.
Replacing the touch sensor board
To replace the touch sensor board
1. Remove the computer cover. Refer to “Removing the computer cover”.
2. Open the system bay. Refer to step 2 of the “Replacing the hard disk
drive” section.
3. Remove the wireless keyboard and mouse receiver module. Refer to
“Replacing the wireless keyboard and mouse receiver module”.
4. Disconnect the touch sensor board cable from the system board.