Panasonic VDRD310 Dvd Camcorder - English/spanish - Page 127

TROUBLESHOOTING, Problem, Check points

Get Panasonic VDRD310 - DVD CAMCORDER PDF manuals and user guides View all Panasonic VDRD310 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 127 highlights

Troubleshooting Others Problem This unit cannot be turned on. This unit is turned off automatically. This unit does not stay on long enough. A clicking sound is heard when the power is turned off. Battery runs down quickly. This unit cannot be operated though it is turned on. This unit does not operate normally. The screen has changed suddenly. Check points ≥ Is the battery fully charged? # Charge the battery using the AC adaptor. (l 28) ≥ The battery protection circuit may have operated. Attach the battery to the AC adaptor for 5 to 10 seconds. If the unit still cannot be used, the battery is faulty. ≥ Is the LCD monitor opened or the viewfinder extended? ≥ If you do not use the unit for approximately 5 minutes, the power is automatically turned off to conserve the battery charge. To resume recording, turn the power back on. The power will not turn off automatically when the power save function (l 117) is set to [OFF]. ≥ Is the battery low? # If the remaining battery power indication is flashing or the message "LOW BATTERY." is displayed, the battery has run down. Charge the battery. (l 28) ≥ This is the sound of the lens moving and is not a malfunction. ≥ Is the battery fully charged? # Charge it with the AC adaptor. (l 28) ≥ Are you using the battery in an extremely cold place? # The battery is affected by ambient temperature. In cold places, the operating time of the battery becomes shorter. ≥ Has the battery worn out? # The battery has a limited life. If the operating time is still too short even after the battery is fully charged, the battery has worn out and can no longer be used. ≥ The unit cannot be operated unless you open the LCD monitor or extend the viewfinder. ≥ Press the RESET button. (l 130) If normal conditions are not restored yet, remove the battery or AC adaptor, wait about 1 minute and then reconnect the battery or AC adaptor. Then about 1 minute later, turn on the power again. (Conducting the above operation when the access lamp is on may destroy the data on the disc or card.) ≥ Has the demonstration started? # If you set [DEMO MODE] to [ON] without inserting a disc or a card in video recording mode or picture recording mode, the unit is automatically set to the demonstration mode for introducing its functions. Normally this should be set to [OFF]. Press the MENU button, then select [SETUP] # [DEMO MODE] # [OFF] and press the joystick. 127 LSQT1145

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
Others
127
LSQT1145
Troubleshooting
Problem
Check points
This unit cannot be
turned on.
≥
Is the battery fully charged?
#
Charge the battery using the AC adaptor. (
l
28)
≥
The battery protection circuit may have operated. Attach the
battery to the AC adaptor for 5 to 10 seconds. If the unit still
cannot be used, the battery is faulty.
≥
Is the LCD monitor opened or the viewfinder extended?
This unit is turned off
automatically.
≥
If you do not use the unit for approximately 5 minutes, the
power is automatically turned off to conserve the battery
charge. To resume recording, turn the power back on.
The power will not turn off automatically when the power save
function (
l
117) is set to [OFF].
This unit does not stay
on long enough.
≥
Is the battery low?
#
If the remaining battery power indication is flashing or the
message “LOW BATTERY.” is displayed, the battery has run
down. Charge the battery. (
l
28)
A clicking sound is heard
when the power is turned
off.
≥
This is the sound of the lens moving and is not a malfunction.
Battery runs down
quickly.
≥
Is the battery fully charged?
#
Charge it with the AC adaptor. (
l
28)
≥
Are you using the battery in an extremely cold place?
#
The battery is affected by ambient temperature. In cold places,
the operating time of the battery becomes shorter.
≥
Has the battery worn out?
#
The battery has a limited life. If the operating time is still too short
even after the battery is fully charged, the battery has worn out
and can no longer be used.
This unit cannot be
operated though it is
turned on.
This unit does not
operate normally.
≥
The unit cannot be operated unless you open the LCD monitor
or extend the viewfinder.
≥
Press the RESET button. (
l
130) If normal conditions are not
restored yet, remove the battery or AC adaptor, wait about 1
minute and then reconnect the battery or AC adaptor. Then
about 1 minute later, turn on the power again. (Conducting the
above operation when the access lamp is on may destroy the
data on the disc or card.)
The screen has changed
suddenly.
≥
Has the demonstration started?
#
If you set [DEMO MODE] to [ON] without inserting a disc or a
card in video recording mode or picture recording mode, the unit
is automatically set to the demonstration mode for introducing its
functions. Normally this should be set to [OFF]. Press the MENU
button, then select [SETUP]
#
[DEMO MODE]
#
[OFF] and
press the joystick.