Panasonic WVCU650 WJSX150 User Guide - Page 9

CAMERA SITE ACCESSORIES CONTROL, Receiver Control

Get Panasonic WVCU650 - SYSTEM CONTROLLER ADDENDUM PDF manuals and user guides
UPC - 791871504277
View all Panasonic WVCU650 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

CAMERA SITE ACCESSORIES CONTROL Note: This section describes the terminal mode. To operate in the PS·Data mode, refer to the operating instructions. ■ Receiver Control The following functions are available only when the receivers are included in the system and the specified camera housing is installed. ● Camera Housing Control Wiper Control 1. Select the desired monitor and camera. (Refer to p. 3 Monitor Selection and p. 3 Camera Selection.) 2. Press the WIPER button to turn on the housing wiper of the camera repeatedly until buttons are released. Defroster Control 1. Select the desired monitor and camera. (Refer to p. 3 Monitor Selection and p. 3 Camera Selection.) 2. Press the DEF ON/OFF button to turn on the housing defroster of the camera. 3. To turn off the defroster, press the DEF ON/OFF button while holding down the SHIFT button. ● Auxiliary Control 1. Select the desired monitor and camera. (Refer to p. 3 Monitor Selection and p. 3 Camera Selection.) 2. Press the AUX1 ON/OFF button to turn on the user's auxiliary switch 1 of the receiver. Press the AUX1 ON/OFF button while holding down the SHIFT button to turn off the user's auxiliary switch 1 of the receiver. 3. Press the AUX2 ON/OFF button to turn on the user's auxiliary switch 2 of the receiver. Press the AUX2 ON/OFF button while holding down the SHIFT button to turn off the user's auxiliary switch 2 of the receiver. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
9
Note:
This section describes the terminal mode. To operate
in the PS·Data mode, refer to the operating instructions.
■
Receiver Control
The following functions are available only when the
receivers are included in the system and the specified
camera housing is installed.
●
Camera Housing Control
Wiper Control
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2.
Press the WIPER button to turn on the housing wiper of
the camera repeatedly until buttons are released.
Defroster Control
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. Press the DEF ON/OFF button to turn on the housing
defroster of the camera.
3. To turn off the defroster, press the DEF ON/OFF button
while holding down the SHIFT button.
●
Auxiliary Control
1. Select the desired monitor and camera. (Refer to p. 3
Monitor Selection and p. 3 Camera Selection.)
2. Press the AUX1 ON/OFF button to turn on the user's
auxiliary switch 1 of the receiver.
Press the AUX1 ON/OFF button while holding down the
SHIFT button to turn off the user's auxiliary switch 1 of
the receiver.
3. Press the AUX2 ON/OFF button to turn on the user's
auxiliary switch 2 of the receiver.
Press the AUX2 ON/OFF button while holding down the
SHIFT button to turn off the user's auxiliary switch 2 of
the receiver.
CAMERA SITE ACCESSORIES CONTROL