Singer One Instruction Manual 4 - Page 11

chainstitching.

Get Singer One PDF manuals and user guides View all Singer One manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

The Even Feed Foot • Guide EvenFeed foot into position from back of machine, making sure the movable arm straddles the needle clamp. Tighten presser-foot screw securely with a coin. To remove, loosen screw and guide foot to the right and away from you. Movable Arm Fit Needle Clamp CHANGING PLATES (Note: Remove bobbin if it contains thread in order to prevent thread being caught when plate is replaced.) 1. Raise take-up lever to its highest position by turning the hand wheel toward you. 2. Raise presser foot. 3. Open slide plate. Press down on front edge of plate and lift up and out. 4. Position new plate over pins and release. Plate is drawn into position by magnets. See special instructions on page 30 for attaching straight-stitch plate for chainstitching. 5. Close slide plate. Changing Even Feed Foot 1i I II 54 3 iii 1 3456 Removing Needle Plate 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
The
Even
Feed
Foot
•
Guide
Even
Feed
foot
into
position
from
back
Movable
of
machine,
making
sure
the
movable
arm
Arm
straddles
the
needle
clamp.
Tighten
presser
-foot
screw
securely
with
a
coin.
To
Fi
t
remove,
loosen
screw
and
guide
foot
to
the
right
and
away
from
you.
Needle
Clamp
Changing
Even
Feed
Foot
CHANGING
PLATES
(Note:
Remove
bobbin
if
it
contains
thread
in
order
to
prevent
thread
being
caught
when
plate
is
replaced.)
1.
Raise
take-up
lever
to
its
highest
position
by
turning
the
hand
wheel
toward
you.
2.
Raise
presser
foot.
3.
Open
slide
plate.
Press
down
on
front
edge
of
plate
and
lift
up
and
out.
4.
Position
new
plate
over
pins
and
release.
Plate
is
drawn
into
position
by
magnets.
See
special
instructions
on
page
30
for
attaching
straight
-stitch
plate
for
chainstitching.
5.
Close
slide
plate.
1i
1
I I
I
54
3
iii
3456
Removing
Needle
Plate
5