Singer One Instruction Manual 4 - Page 16

approximately

Get Singer One PDF manuals and user guides View all Singer One manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Flo 3. 10 USING THE NEEDLE THREADER The needle threader may be purchased separately at your local Singer Sewing Center. Thread the machine in the usual way up to the needle, then follow the instructions below. • Turn hand wheel toward you to raise needle to its highest position. • Lower the presser foot. 1 . Holding the needle threader by its tab with the right hand, position U-shaped part of threader under bar of needle clamp. Snap threader up onto bar. • Slide threader over to left, as far as it will go. 2. Swing threader back just far enough to clear the needle. Align metal hook of threader with the eye of the needle. • Swing threader forward so that hook passes through eye of needle. 3. Holding approximately 3 inches (7.6cm) of thread between your hands, loop thread under metal hook. Leave slack in thread on each side of hook. Release thread. 4. Holding threader by its tab with right hand, draw metal hook and thread back through eye of needle. • Slide threader to the right off bar of needle clamp. Carefully unhook thread from needle threader.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
USING
THE
NEEDLE
THREADER
The
needle
threader
may
be
purchased
sepa-
rately
at
your
local
Singer
Sewing
Center.
Thread
the
machine
in
the
usual
way
up
to
the
needle,
then
follow
the
instructions
below.
•
Turn
hand
wheel
toward
you
to
raise
needle
to
its
highest
position.
•
Lower
the
presser
foot.
3.
Flo
1
.
Holding
the
needle
threader
by
its
tab
with
the
right
hand,
position
U-shaped
part
of
threader
under
bar
of
needle
clamp.
Snap
threader
up
onto
bar.
•
Slide
threader
over
to
left,
as
far
as
it
will
go.
2.
Swing
threader
back
just
far
enough
to
clear
the
needle.
Align
metal
hook
of
threader
with
the
eye
of
the
needle.
•
Swing
threader
forward
so
that
hook
passes
through
eye
of
needle.
3.
Holding
approximately
3
inches
(7.6cm)
of
thread
between
your
hands,
loop
thread
under
metal
hook.
Leave
slack
in
thread
on
each
side
of
hook.
Release
thread.
4.
Holding
threader
by
its
tab
with
right
hand,
draw
metal
hook
and
thread
back
through
eye
of
needle.
•
Slide
threader
to
the
right
off
bar
of
needle
clamp.
Carefully
unhook
thread
from
needle
threader.
10