Singer One Instruction Manual 4 - Page 19

AI II

Get Singer One PDF manuals and user guides View all Singer One manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Replacing a Wound Bobbin REPLACING A WOUND BOBBIN Raise take-up lever to its highest position. 1. Open slide plate; move bobbin latch all the way to the left. 2. Draw about an inch of thread from bobbin and place bobbin in case. 3. Pull thread into bobbin-case slot (point 1), draw it under flat spring and around to (or slightly past) point 2, leaving two or three inches of free thread. (Leave slide plate open.) RAISING THE BOBBIN THREAD Set stitch width dial at 1. Move bobbin latch to right (sewing position). Hold needle thread lightly with left hand and turn hand wheel slowly toward you so the needle enters plate. 2. Continue turning hand wheel and holding needle thread until needle rises. Tighten your hold on the needle thread and bring up bobbin thread in a loop. 3. Open the loop with your fingers, draw needle and bobbin threads under the presser foot and place them diagonally to right or left. Then close the slide plate. Pull Thread into Slot 1 I Insert Bobbin rs I Flat Spring Draw Thread Under Flat Spring Around to Point 2 Raising the Bobbin Thread ii Step 1 Step 2 Step 3 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
REPLACING
A
WOUND
BOBBIN
Raise
take-up
lever
to
its
highest
position.
1.
Open
slide
plate;
move
bobbin
latch
all
the
way
to
the
left.
2.
Draw
about
an
inch
of
thread
from
bobbin
and
place
bobbin
in
case.
3.
Pull
thread
into
bobbin
-case
slot
(point
1),
draw
it
under
flat
spring
and
around
to
(or
Replacing
a
Wound
Bobbin
Insert
Bobbin
slightly
past)
point
2,
leaving
two
or
three
rs
I
inches
of
free
thread.
(Leave
slide
plate
open.)
Pull
Thread
into
Slot
1
Flat
Spring
RAISING
THE
BOBBIN
THREAD
Set
stitch
width
dial
at
1.
Move
bobbin
latch
to
right
(sewing
posi-
tion).
Hold
needle
thread
lightly
with
left
hand
and
turn
hand
wheel
slowly
toward
you
so
the
needle
enters
plate.
2.
Continue
turning
hand
wheel
and
holding
needle
thread
until
needle
rises.
Tighten
your
hold
on
the
needle
thread
and
bring
up
bobbin
thread
in
a
loop.
I
I
Draw
Thread
Under
Flat
Spring
Around
to
Point
2
3.
Open
the
loop
with
your
fingers,
draw
nee-
dle
and
bobbin
threads
under
the
presser
foot
and
place
them
diagonally
to
right
or
left.
Then
close
the
slide
plate.
Raising
the
Bobbin
Thread
i
i
Step
1
Step
2
Step
3
13