Sony VPLHS3 Operating Instructions - Page 19

Turn the FOCUS ring to adjust, the focus again., When projecting from the center

Get Sony VPLHS3 - Cineza Digital Home Entertainment LCD Front Projector PDF manuals and user guides
UPC - 027242628793
View all Sony VPLHS3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Connections and Preparations 4 Adjust to correct horizontal trapezoidal distortion using SIDE SHOT + or -. SIDE SHOT are parallel to the vertical frame ends of the screen, as shown below. Press SIDE SHOT + or - so that the upper side of the picture becomes parallel to the bottom side. If the right side is longer than the left side, press SIDE SHOT +. If the left side is longer than the right side, press SIDE SHOT -. To fine-adjust the distortion, press M or m. Note Even when projecting using "Side Shot," four sides of a picture may sometimes not be parallel to the sides of a screen frame. When projecting from the center 1 Set the "V Keystone" in the INSTALL SETTING menu to "Auto." Note "V Keystone" in the INSTALL SETTING menu is set to "Manual" in the default. If it is set to "Auto," the vertical distortion of the picture will be automatically corrected. The "V Keystone" adjustment may not correct trapezoidal distortion perfectly, depending on the room temperature or the screen angle. In this case, set manually by value adjustment. 2 Position the projector so that the upper and bottom sides of the picture are parallel to the horizontal frame ends of the screen, and the left and right sides of the picture If the picture does not overlaps on the screen as shown above, confirm and adjust the installation position of the projector and screen referring to "Installing the Projector and a Screen" (1 page 7). If the left and right sides of the picture are not parallel to the left and right sides of the screen, set "V Keystone" in the INSTALL SETTING menu to "Manual," press ENTER, then adjust with M or m so that they become parallel. 3 Adjust so that both ends of the bottom side of the picture fit those of the bottom side of the screen using the adjuster and the ZOOM ring. 8 Turn the FOCUS ring to adjust the focus again. 19 Step 3: Adjusting the Picture Size and Position GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
Connections and
Preparations
19
GB
Step 3: Adjusting the Picture Size and Position
4
Adjust to correct horizontal trapezoidal
distortion using SIDE SHOT + or –.
Press SIDE SHOT + or – so that the upper side of
the picture becomes parallel to the bottom side. If
the right side is longer than the left side, press
SIDE SHOT +. If the left side is longer than the
right side, press SIDE SHOT –. To fine-adjust the
distortion, press
M
or
m
.
Note
Even when projecting using “Side Shot,” four sides of a picture
may sometimes not be parallel to the sides of a screen frame.
When projecting from the center
1
Set the “V Keystone” in the INSTALL
SETTING menu to “Auto."
Note
“V Keystone” in the INSTALL SETTING menu is set to
“Manual” in the default. If it is set to “Auto,” the vertical distortion
of the picture will be automatically corrected. The “V Keystone”
adjustment may not correct trapezoidal distortion perfectly,
depending on the room temperature or the screen angle. In this
case, set manually by value adjustment.
2
Position the projector so that the upper
and bottom sides of the picture are parallel
to the horizontal frame ends of the screen,
and the left and right sides of the picture
are parallel to the vertical frame ends of
the screen, as shown below.
If the picture does not overlaps on the screen as
shown above, confirm and adjust the installation
position of the projector and screen referring to
“Installing the Projector and a Screen” (
1
page
7).
If the left and right sides of the picture are not
parallel to the left and right sides of the screen, set
“V Keystone” in the INSTALL SETTING menu to
“Manual,” press ENTER, then adjust with
M
or
m
so that they become parallel.
3
Adjust so that both ends of the bottom
side of the picture fit those of the bottom
side of the screen using the adjuster and
the ZOOM ring.
8
Turn the FOCUS ring to adjust
the focus again.
SIDE SHOT