Tripp Lite SU3000RTXLCD2U Owner's Manual for SU3000RTXLCD2U UPS System 9332C3 - Page 17

Scroll, Select

Get Tripp Lite SU3000RTXLCD2U PDF manuals and user guides View all Tripp Lite SU3000RTXLCD2U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Operation UPS Setup Order of Operations To access the UPS Setup screens, press both the SCROLL (v) and SELECT (^) buttons simultaneously and hold for 3 seconds. 1 The OUTPUT VOLTAGE selection screen will appear. OUTPUT VOLTAGE refers to the nominal output voltage of the UPS. This value is most commonly set to match the prevailing country or region-specific nominal voltage. In general, use 120V for USA and Canada, 127V for Mexico and 100V for Japan. Additional values of 110 & 115V are also available. Note: Certain voltage settings will cause automatic de-rating. See specifications on unit label for de-rating info. To Advance to the Next Screen: Press SCROLL (v) To Change This Setting: Press "SELECT" (^) Note: The UPS must be in Standby Mode to change this setting. 120V* SCROLL SELECT Press "SELECT" (^) to SET this value. Press "SCROLL" (v) to advance to the next option. Available values are: 100, 110, 115, 120 & 127V Press SCROLL (v) to browse options and press SELECT (^) to SET. Factory default = 120V 2 The OUTPUT FREQUENCY selection screen will appear. OUTPUT FREQUENCY refers to the cycles-per-second (Hz) of UPS output power. This value is most commonly set to match the prevailing country or region-specific frequency. In general, in the USA, Canada and Mexico use the 60Hz factory setting. In 100-127V 50Hz locations, such as Jamaica, Antigua and parts of Japan, set the UPS to 50Hz. To successfully configure your UPS to convert frequency from 50-to-60Hz or 60-to-50Hz, set BOTH the OUTPUT FREQUENCY to the desired setting and enable this function by setting the FREQ CONVERSION to ENABLE. To Advance to the Next Screen: Press SCROLL (v) To Change This Setting: Press "SELECT" (^) Note: The UPS must be in Standby Mode to change this setting. 60HZ* SCROLL SELECT 3 The BYPASS RANGE selection screen will appear. Press "SELECT" (^) to SET this value. Press "SCROLL" (v) to advance to the next option. Available values are: 60Hz, 50Hz Scroll through available values and press SELECT (^) to SET. Factory default = 60Hz BYPASS RANGE: When ECONOMY MODE is enabled, this UPS will allow line voltage that's already of sufficient quality pass through to connected equipment unchanged. The BYPASS RANGE control gives users the ability to control the amount of deviation from the selected nominal voltage before automatically turning back to on-line mode. The factory setting of WIDE is compatible with the vast majority of networking equipment. Using this control, users of even the most sensitive equipment can utilize the UPS in economy mode by selecting alternate preset values. Regardless of the "plus or minus" value entered, the highest bypass voltage available is 135V. The lowest bypass voltage available is 90V (full load) and 70V (

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
 


120V*
SCROLL
SELECT
 


60HZ*
SCROLL
SELECT
 


WIDE*
SCROLL
SELECT
Continued on page 18.
17
Operation
UPS Setup Order of Operations
To access the UPS Setup screens, press both the SCROLL (
v
) and SELECT (^) buttons simultaneously and hold for 3 seconds.
1
The OUTPUT VOLTAGE selection screen will appear.
OUTPUT VOLTAGE refers to the nominal output voltage of the UPS. This value is most
commonly set to match the prevailing country or region-specific nominal voltage. In general,
use 120V for USA and Canada, 127V for Mexico and 100V for Japan. Additional values of
110 & 115V are also available.
Note: Certain voltage settings will cause automatic de-rating.
See specifications on unit label for de-rating info.
Press “SELECT” (
^
) to SET this value.
Press “SCROLL” (
v
) to advance to the next option.
Available values are: 100, 110, 115, 120 &
127V
Press SCROLL (
v
) to browse options
and press SELECT (
^
) to SET.
Factory default = 120V
2
The OUTPUT FREQUENCY selection screen will appear.
OUTPUT FREQUENCY refers to the cycles-per-second (Hz) of UPS output power. This value is
most commonly set to match the prevailing country or region-specific frequency. In general,
in the USA, Canada and Mexico use the 60Hz factory setting. In 100-127V 50Hz locations,
such as Jamaica, Antigua and parts of Japan, set the UPS to 50Hz. To successfully configure
your UPS to convert frequency from 50-to-60Hz or 60-to-50Hz, set BOTH the OUTPUT
FREQUENCY to the desired setting and enable this function by setting the FREQ
CONVERSION to ENABLE.
To Change This
Setting:
Press “SELECT” (
^
)
To Advance to
the Next Screen:
Press SCROLL (
v
)
To Change This
Setting:
Press “SELECT” (
^
)
Press “SELECT” (
^
) to SET this value.
Press “SCROLL” (
v
) to advance to the next option.
Available values are: 60Hz, 50Hz
Scroll through available values and press
SELECT (
^
) to SET.
Factory default = 60Hz
To Advance to
the Next Screen:
Press SCROLL (
v
)
3
The BYPASS RANGE selection screen will appear.
BYPASS RANGE: When ECONOMY MODE is enabled, this UPS will allow line voltage that’s
already of sufficient quality pass through to connected equipment unchanged. The BYPASS
RANGE control gives users the ability to control the amount of deviation from the selected
nominal voltage before automatically turning back to on-line mode. The factory setting of
WIDE is compatible with the vast majority of networking equipment. Using this control, users
of even the most sensitive equipment can utilize the UPS in economy mode by selecting
alternate preset values. Regardless of the “plus or minus” value entered, the highest bypass
voltage available is 135V. The lowest bypass voltage available is 90V (full load) and 70V
(<70% load). The “Wide” range reflects these same values (full load 90 to 135V / <70%
load 70 to 135V).
To Change This
Setting:
Press “SELECT” (
^
)
Press “SELECT” (
^
) to SET this value.
Press “SCROLL” (
v
) to advance to the next option.
Available values are: +/-5, 6, 7, 8, 9, 10, 11,
12, 13, 14, 15% & wide
Scroll through available values and press
SELECT (
^
) to SET.
Factory default = WIDE
To Advance to
the Next Screen:
Press SCROLL (
v
)
Note: The UPS must be
in Standby Mode to
change this setting.
Note: The UPS must be
in Standby Mode to
change this setting.
13-07-015-9332C3.indb
17
7/26/2013
11:16:23 AM