Yamaha DG80-112A Owner's Manual - Page 12
Utility Mode
View all Yamaha DG80-112A manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
DG100-212A/DG80-210A/DG80-112A/DG130HA Utility Mode The Utility Mode is used to perform MIDI settings, set the speaker simulator and volume pedal position settings. To enter the Utility Mode, press and hold the button for more than one second, the "UTIL." mode display lamp will light. Each of the settings will be stored in memory, even when the power to the amp is turned off. To exit from the Utility Mode, press the button, the "AMP" (amp mode) display lamp will light. * MIDI messages cannot be received when in the Utility Mode so, refer to the "Using MIDI to Recall Memory", "Using MIDI to Control Volume", "Controlling Reverb, Tremolo, Chorus and Tape Echo via MIDI" and "MIDI Bulk In" sections in this manual to perform the corresponding MIDI operations. s Creating a Program Change Table With this procedure, a specific memory number in the DG amplifier's internal memory can be recalled with a program change number received from an external MIDI device. * Factory Preset: Program Change Number = Memory Number. 1. Press and hold the button for more than one second. The "UTIL." mode display lamp will light. (Utility Mode) 2. Press the button. 3. Using the / buttons, select the program change number (1 - 2.8) that will be sent by the external device. The number will appear on the display. 4. Press the button. 5. Using the / buttons, select the memory number (1 - 28. ) to be recalled from the DG amplifier's internal memory. The number will appear on the display. 6. Depending upon your particular needs, repeat steps 2 through 5 as needed. s Set the MIDI Receive Channel Set the DG amplifier's MIDI receive channel. * To transmit and receive MIDI data between MIDI devices, the MIDI channel on both devices must be the same or data will not be successfully transferred. (The factory preset is channel 1.) 1. Press and hold the button for more than one second. The "UTIL." mode display will light. (Utility Mode) 2. Press the button. The currently set MIDI receive channel will appear on the display. 3. Use the / All, oF). button to select a MIDI receive channel (1 - 16, * With the "All" setting omni is set to on. s MIDI Bulk Out You can back up the data stored in the DG amplifier's internal memory by saving the data to an external MIDI storage device (Yamaha MDF3, etc.). 1. With a MIDI cable, connect the DG amplifier's MIDI OUT jack to the MIDI IN jack on the external MIDI storage device. 2. Press the button for more than one second. The "UTIL." mode display lamp will light. 3. To transmit all memory (128 memory, plus Utility setting data) with the Bulk Out operation: → Press the button. "All" will appear in the display. To transmit a single memory: → Press the button. Use the / button to select the memory number (1 - 128, All) that you want to save with the Bulk Out operation. * When "All" is selected in the Bulk Out operation, all memory data (128 memory) will be transmitted. 4. Press the button to execute the Bulk Out operation. Press the button to cancel the operation. * The device number is the same as that of the MIDI receive channel. If the MIDI receive channel is set to "All" (Omni ON) the device number will be 1. DG amplifier Rear Panel MIDI OUT MIDI Cable MIDI IN s Set the MIDI Merge If you want the MIDI signal received by the DG amplifier's MIDI IN jack to be transmitted on to other MIDI devices via the DG amplifier's MIDI OUT jack, set the MIDI Merge to "on" (ON). If you don't want the data to be transmitted, set to "oF" (OFF). 1. Press and hold the button for more than one second. The "UTIL." mode display will light. 2. Press the button. The currently set MIDI merge setting will appear in the display. 3. Use the / button to select either "on" or "oF". External MIDI Device s MIDI Bulk In With a MIDI cable, connect the DG amplifier's MIDI IN jack to the MIDI OUT jack on an external MIDI device. Return your MIDI back up data to the DG amplifier. * The MIDI Bulk In operation is carried out in the AMP or EFFECT modes only. It can not be carried out in the Utility Mode. * The device number is the same as that of the MIDI receive channel. If the MIDI receive channel is set to "All" (Omni On), the MIDI channel will be set to 1. The DG amplifier will not receive data if the MIDI channel is set to "oF" (OFF). * "Ld" is shown on the display while the MIDI Bulk In operation is being executed. 12