Home » ZyXEL Manuals » Networking » ZyXEL P-660HNU-F1 » Manual Viewer

ZyXEL P-660HNU-F1 User Guide - Page 94

Table 12, DESCRIPTION, Routing, PPP over Ethernet PPPoE, IP over Ethernet, PPP over ATM

Get ZyXEL P-660HNU-F1 PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

Chapter 5 Broadband The following table describes the fields in this screen. Table 12 Broadband Add/Edit: Routing- IPoE Label DESCRIPTION General Name Enter a service name of the connection. Type ADSL: The ZyXEL Device uses the ADSL technology for data transmission over the DSL port. Mode Select Routing (default) from the drop-down list box if your ISP give you one IP address only and you want multiple computers to share an Internet account. WAN Service Type This field is available only when you select Routing in the Mode field. Select the method of encapsulation used by your ISP. ATM PVC Configuration VPI VCI DSL Link Type Encapsulation Mode Service Category • PPP over Ethernet (PPPoE) - PPPoE (Point to Point Protocol over Ethernet) provides access control and billing functionality in a manner similar to dial-up services using PPP. Select this if you have a username and password for Internet access. • IP over Ethernet - In this type of Internet connection, IP packets are routed between the Ethernet interface and the WAN interface and then formatted so that they can be understood in a bridged environment. • PPP over ATM - PPPoA offers standard PPP features, such as authentication, encryption, and compression. It is used as the connection encapsulation method in an ATM based network, and it can reduce overhead slightly compared to PPPoE. VPI (Virtual Path Identifier) and VCI (Virtual Channel Identifier) define a virtual circuit. This section is available only when you select ADSL in the Type field to configure an ATM layer-2 interface. The valid range for the VPI is 0 to 255. Enter the VPI assigned to you. The valid range for the VCI is 32 to 65535 (0 to 31 is reserved for local management of ATM traffic). Enter the VCI assigned to you. The DSL link type is set to EoA (Ethernet over ATM) to have an Ethernet header in the packet, so that you can have multiple services/connections over one PVC. You can set each connection to have its own MAC address or all connections share one MAC address but use different VLAN IDs for different services. EoA supports IPoE, PPPoE and RFC1483/2684 bridging encapsulation methods. The encapsulation method of multiplexing used by your is LLC/SNAP-BRIDGING. In LCC encapsulation, bridged PDUs are encapsulated by identifying the type of the bridged media in the SNAP header. Select UBR Without PCR for applications that are non-time sensitive, such as e-mail. Select CBR (Constant Bit Rate) to specify fixed (always-on) bandwidth for voice or data traffic. Select Non Realtime VBR (non real-time Variable Bit Rate) for connections that do not require closely controlled delay and delay variation. Peak Cell Rate Sustainable Cell Rate Maximum Burst Size Select Realtime VBR (real-time Variable Bit Rate) for applications with bursty connections that require closely controlled delay and delay variation. Divide the DSL line rate (bps) by 424 (the size of an ATM cell) to find the Peak Cell Rate (PCR). This is the maximum rate at which the sender can send cells. Type the PCR here. The Sustain Cell Rate (SCR) sets the average cell rate (long-term) that can be transmitted. Type the SCR, which must be less than the PCR. Note that system default is 0 cells/sec. Maximum Burst Size (MBS) refers to the maximum number of cells that can be sent at the peak rate. Type the MBS, which is less than 65535. 94 ADSL Series User's Guide

Section	Page
ADSL Router Series	1
Videos	2
About This User's Guide	3
Document Conventions	5
Safety Warnings	7
Contents Overview	9
Table of Contents	11
User’s Guide	19
Introduction	21
1.1 Overview	21
1.2 Applications for the ZyXEL Device	21
1.2.1 Internet Access	21
1.2.2 Wireless Connection	22
1.2.3 ZyXEL Device’s USB and Print Server Support	22
1.3 The WPS/WLAN Button	23
1.4 Ways to Manage the ZyXEL Device	24
1.5 Good Habits for Managing the ZyXEL Device	25
1.6 The RESET Button	25
Introducing the Web Configurator	27
2.1 Overview	27
2.1.1 Accessing the Web Configurator	27
2.2 The Web Configurator Layout	29
2.2.1 Title Bar	29
2.2.2 Main Window	30
2.2.3 Navigation Panel	30
2.3 User Mode	32
2.3.1 Overview	32
2.3.2 What You Can Do	32
2.3.3 Navigation Panel	33
2.3.4 Network Map	33
2.3.5 Control Panel	34
2.3.6 Power Saving	34
2.3.7 Content Filter	35
2.3.8 Firewall	36
2.3.9 Wireless Security	37
2.3.10 WPS	38
2.3.11 Media Server	38
Tutorials	41
3.1 Overview	41
3.2 Setting Up Your DSL Connection	41
3.3 How to Set up a Wireless Network	44
3.3.1 Example Parameters	44
3.3.2 Configuring the ADSL Device	44
3.3.3 Connecting Wirelessly to your ADSL Device	46
3.3.4 Configuring the Wireless Client using the WPS PIN number	48
3.4 Setting Up NAT Port Forwarding to Allow Access to Network Servers from the Internet	49
3.5 Using the File Sharing Feature	50
3.5.1 Set Up File Sharing	51
3.5.2 Access Your Shared Files From a Computer	54
3.6 Using the Print Server Feature	56
3.7 Configuring the MAC Address Filter for Restricting Wireless Internet Access	70
3.8 Configuring Static Route for Routing to Another Network	71
3.9 Configuring QoS Queue and Class Setup	73
3.10 Access the ADSL Device Using DDNS	77
3.10.1 Registering a DDNS Account on www.dyndns.org	78
3.10.2 Configuring DDNS on Your ADSL Device	78
3.10.3 Testing the DDNS Setting	79
Technical Reference	81
Connection Status and System Info Screens	83
4.1 Overview	83
4.2 The Connection Status Screen	83
4.3 The System Info Screen	84
Broadband	87
5.1 Overview	87
5.1.1 What You Can Do in this Chapter	87
5.1.2 What You Need to Know	87
5.1.3 Before You Begin	88
5.2 The Broadband Screen	88
5.2.1 Add/Edit Internet Connection	89
5.3 Technical Reference	100
Wireless	105
6.1 Overview	105
6.1.1 What You Can Do in this Chapter	105
6.1.2 Wireless Network Overview	105
6.1.3 Before You Begin	107
6.2 The Wireless General Screen	107
6.2.1 No Security	109
6.2.2 Basic (Static WEP/Shared WEP Encryption)	109
6.2.3 More Secure (WPA(2)-PSK)	111
6.2.4 WPA(2) Authentication	112
6.3 The More AP Screen	113
6.3.1 Edit More AP	114
6.4 The WPS Screen	115
6.5 The WMM Screen	117
6.6 Scheduling Screen	118
6.7 Technical Reference	119
6.7.1 Additional Wireless Terms	119
6.7.2 Wireless Security Overview	119
6.7.3 Signal Problems	122
6.7.4 BSS	122
6.7.5 MBSSID	122
6.7.6 WiFi Protected Setup (WPS)	123
Home Networking	131
7.1 Overview	131
7.1.1 What You Can Do in this Chapter	131
7.1.2 What You Need To Know	131
7.2 The LAN Setup Screen	134
7.3 The Static DHCP Screen	136
7.3.1 Before You Begin	136
7.4 The UPnP Screen	137
7.5 The File Sharing Screen	138
7.5.1 Before You Begin	139
7.5.2 Add/Edit File Sharing	140
7.5.3 Add New User	141
7.6 The Media Server Screen	142
7.6.1 The Media Server Screen	142
7.7 The Print Server Screen	143
7.7.1 Before You Begin	143
7.8 Technical Reference	144
7.9 Installing UPnP in Windows Example	148
7.10 Using UPnP in Windows XP Example	151
Routing	157
8.1 Overview	157
8.2 Configuring Static Route	157
8.2.1 Add/Edit Static Route	158
DNS Route	161
9.1 Overview	161
9.1.1 What You Can Do in this Chapter	161
9.2 The DNS Route Screen	162
9.2.1 Add/Edit DNS Route Edit	162
Quality of Service (QoS)	165
10.1 Overview	165
10.1.1 What You Can Do in this Chapter	165
10.1.2 What You Need to Know	165
10.2 The QoS General Screen	166
10.3 The Queue Setup Screen	167
10.3.1 Add/Edit a QoS Queue	168
10.4 The Class Setup Screen	169
10.4.1 Add/Edit QoS Class	170
10.5 The QoS Monitor Screen	173
10.6 QoS Technical Reference	173
10.6.1 IP Precedence	174
10.6.2 DiffServ	174
Network Address Translation (NAT)	175
11.1 Overview	175
11.1.1 What You Can Do in this Chapter	175
11.1.2 What You Need To Know	175
11.2 The Port Forwarding Screen	176
11.2.1 The Port Forwarding Screen	177
11.2.2 The Port Forwarding Edit Screen	177
11.3 The Sessions Screen	178
11.4 The ALG Screen	179
11.5 Technical Reference	180
11.5.1 NAT Definitions	180
11.5.2 What NAT Does	180
11.5.3 How NAT Works	180
Dynamic DNS	183
12.1 Overview	183
12.1.1 What You Need To Know	183
12.2 The Dynamic DNS Screen	183
Firewall	185
13.1 Overview	185
13.1.1 What You Can Do in this Chapter	185
13.1.2 What You Need to Know	185
13.2 The General Screen	186
13.3 The Services Screen	187
13.4 Firewall Technical Reference	188
13.4.1 Guidelines For Enhancing Security With Your Firewall	188
13.4.2 Security Considerations	188
MAC Filter	191
14.1 Overview	191
14.1.1 What You Need to Know	191
14.2 The MAC Filter Screen	191
Certificates	193
15.1 Overview	193
15.1.1 What You Can Do in this Chapter	193
15.1.2 What You Need to Know	193
15.1.3 Verifying a Certificate	195
15.2 Local Certificates	196
15.2.1 Trusted CAs	197
15.2.2 Trusted CA Import	198
15.2.3 View Certificate	198
15.3 VPN Certificates	199
15.3.1 Import Certificate	200
VPN	203
16.1 Overview	203
16.1.1 What You Can Do in the VPN Screens	203
16.1.2 What You Need to Know About IPSec VPN	203
16.1.3 Before You Begin	205
16.2 VPN Setup Screen	205
16.3 The VPN Edit Screen	206
16.4 Configuring Advanced Settings	210
16.5 Viewing SA Monitor	212
16.6 IPSec VPN Technical Reference	212
16.6.1 IPSec Architecture	212
16.6.2 IPSec and NAT	213
16.6.3 VPN, NAT, and NAT Traversal	214
16.6.4 Encapsulation	215
16.6.5 IKE Phases	216
16.6.6 Negotiation Mode	217
16.6.7 Remote DNS Server	217
16.6.8 ID Type and Content	218
16.6.9 Pre-Shared Key	219
16.6.10 Diffie-Hellman (DH) Key Groups	219
16.6.11 Telecommuter VPN/IPSec Examples	219
System Monitor	223
17.1 Overview	223
17.1.1 What You Can Do in this Chapter	223
17.2 The WAN Status Screen	223
17.3 The LAN Status Screen	224
17.4 The NAT Status Screen	225
User Account	227
18.1 Overview	227
18.2 The User Account Screen	227
Remote MGMT	229
19.1 Overview	229
19.1.1 What You Need to Know	229
19.2 The Remote MGMT Screen	229
System	231
20.1 Overview	231
20.1.1 What You Need to Know	231
20.2 The System Screen	231
Time Setting	233
21.1 Overview	233
21.2 The Time Setting Screen	233
Log Setting	235
22.1 Overview	235
22.2 The Log Setting Screen	235
Firmware Upgrade	237
23.1 Overview	237
23.2 The Firmware Screen	237
Backup/Restore	239
24.1 Overview	239
24.2 The Backup/Restore Screen	239
24.3 The Reboot Screen	241
Diagnostic	243
25.1 Overview	243
25.1.1 What You Can Do in this Chapter	243
25.2 The Ping Screen	243
25.3 The DSL Line Screen	244
Troubleshooting	247
26.1 Overview	247
26.2 Power, Hardware Connections, and LEDs	247
26.3 ZyXEL Device Access and Login	248
26.4 Internet Access	250
26.5 Wireless Internet Access	251
26.6 USB Device Connection	252
26.7 UPnP	253
Product Specifications	255
IP Addresses and Subnetting	263
Setting Up Your Computer’s IP Address	273
Pop-up Windows, Java Script and Java Permissions	303
Wireless LANs	311
Common Services	331
Open Software Announcements	335
Legal Information	357

Match case Limit results 1 per page

Chapter 5 Broadband

ADSL Series User’s Guide

The following table describes the fields in this screen.

Table 12

Broadband Add/Edit: Routing- IPoE

Label

DESCRIPTION

General

Name

Enter a service name of the connection.

Type

ADSL

: The ZyXEL Device uses the ADSL technology for data transmission over the

DSL port.

Mode

Select

Routing

(default) from the drop-down list box if your ISP give you one IP

address only and you want multiple computers to share an Internet account.

WAN Service Type

This field is available only when you select

Routing

in the

Mode

field. Select the

method of encapsulation used by your ISP.

•

PPP over Ethernet (PPPoE)

- PPPoE (Point to Point Protocol over Ethernet)

provides access control and billing functionality in a manner similar to dial-up

services using PPP. Select this if you have a username and password for Internet

access.

•

IP over Ethernet

- In this type of Internet connection, IP packets are routed

between the Ethernet interface and the WAN interface and then formatted so that

they can be understood in a bridged environment.

•

PPP over ATM

- PPPoA offers standard PPP features, such as authentication,

encryption, and compression. It is used as the connection encapsulation method in

an ATM based network, and it can reduce overhead slightly compared to PPPoE.

ATM PVC

Configuration

VPI (Virtual Path Identifier) and VCI (Virtual Channel Identifier) define a virtual circuit.

This section is available only when you select

ADSL

in the

Type

field to configure an

ATM layer-2 interface.

VPI

The valid range for the VPI is 0 to 255. Enter the VPI assigned to you.

VCI

The valid range for the VCI is 32 to 65535 (0 to 31 is reserved for local management

of ATM traffic). Enter the VCI assigned to you.

DSL Link Type

The DSL link type is set to

EoA

(Ethernet over ATM) to have an Ethernet header in the

packet, so that you can have multiple services/connections over one PVC. You can set

each connection to have its own MAC address or all connections share one MAC

address but use different VLAN IDs for different services.

EoA

supports IPoE, PPPoE

and RFC1483/2684 bridging encapsulation methods.

Encapsulation Mode

The encapsulation method of multiplexing used by your is

LLC/SNAP-BRIDGING

. In

LCC encapsulation, bridged PDUs are encapsulated by identifying the type of the

bridged media in the SNAP header.

Service Category

Select

UBR Without PCR

for applications that are non-time sensitive, such as e-mail.

Select

CBR

(Constant Bit Rate) to specify fixed (always-on) bandwidth for voice or

data traffic.

Select

Non Realtime VBR

(non real-time Variable Bit Rate) for connections that do

not require closely controlled delay and delay variation.

Select

Realtime VBR

(real-time Variable Bit Rate) for applications with bursty

connections that require closely controlled delay and delay variation.

Peak Cell Rate

Divide the DSL line rate (bps) by 424 (the size of an ATM cell) to find the Peak Cell

Rate (PCR). This is the maximum rate at which the sender can send cells. Type the

PCR here.

Sustainable Cell

Rate

The Sustain Cell Rate (SCR) sets the average cell rate (long-term) that can be

transmitted. Type the SCR, which must be less than the PCR. Note that system default

is 0 cells/sec.

Maximum Burst

Size

Maximum Burst Size (MBS) refers to the maximum number of cells that can be sent at

the peak rate. Type the MBS, which is less than 65535.