Alpine CDA-9887 Owners Manual - Page 16
Setting EQ mode, Adjusting and Storing the Parametric, Equalizer Curve, Adjusting and Storing - bluetooth
UPC - 793276711373
View all Alpine CDA-9887 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 16 highlights
Setting EQ mode This setting gives you a choice of 5-band parametric, or 7-band graphic equalizer. 1 Press and hold FUNC./SETUP for at least 2 seconds to setup the Selection mode. 2 Turn the Rotary encoder to select AUDIO mode, and then press / /ENT. Bluetooth GENERAL TUNER* Bluetooth AUDIO DISPLAY * Only when HD Radio/SAT Radio is connected. 3 Turn the Rotary encoder to select EQ Mode, and then press / /ENT. 4 Turn the Rotary encoder to select the desired equalizer characteristic, and then press / /ENT. Parametric EQ (Initial setting) Graphic EQ PEQ: 5-band Parametric EQ (Initial setting) GEQ: 7-band Graphic EQ 5 Press and hold FUNC./SETUP for at least 2 seconds to return to normal mode. • Pressing /RTN during the procedure will return to the previous mode. • If no operation is performed for 60 seconds in the SETUP mode, the setting mode is canceled. • This function is inoperable when DEFEAT is set to ON (page 13). • Press and hold /ESC for at least 2 seconds, the setting mode is canceled. Adjusting and Storing the Parametric Equalizer Curve You can modify the Equalizer settings to create a response curve more appealing to your personal taste. To adjust the Parametric Equalizer Curve, set the EQ mode to Parametric EQ. For details, refer to "Setting EQ mode" (page 14). 1 Press A.SEL to recall the DSP adjust mode. Media Xpander Crossover T.Correction Parametric EQ/Graphic EQ Media Xpander 2 Turn the Rotary encoder to select Parametric EQ mode, and then press / /ENT. 3 Press BAND to select the band to be adjusted. Band1 Band2 Band3 Band4 Band5 Band1 4 Press or to select frequency bands. Adjustable frequency bands: 20 Hz to 20 kHz (in 1/3 octave steps) Band-1: 20 Hz~80 Hz (63 Hz) Band-2: 50 Hz~200 Hz (150 Hz) Band-3: 125 Hz~3.2 kHz (400 Hz) Band-4: 315 Hz~8 kHz (1 kHz) Band-5: 800 Hz~20 kHz (2.5 kHz) 5 Turn the Rotary encoder to adjust the level. Adjustable level: -6 to +6 dB 14-EN 6 Press SOURCE/ to set the bandwidth (Q). Adjustable bandwidth: 1, 1.5, 3 7 To adjust another band, repeat steps 3 to 6 and adjust all bands. 8 When the setting has been completed, select any one of the preset buttons (1 through 6), press and hold the desired preset buttons for at least 2 seconds. 9 Turn the Rotary encoder to select PROTECT YES/NO, and then press / /ENT to store the adjusted contents. PROTECT YES (Initial setting) PROTECT NO • If YES is selected, the adjusted contents are protected and stored into the preset buttons. When you want to store the parameter into a protected preset button, "REPLACE NO/YES" can be selected. • If NO is selected, the preset is stored. 10 After setting, press and hold /ESC for at least 2 seconds to return to normal mode. • The frequencies of adjacent bands cannot be adjusted within 4 steps. • This function is inoperable when DEFEAT is set to ON (page 13). • While adjusting the Parametric EQ, you should consider the frequency response of the connected speakers. • The stored contents are not deleted even when resetting the unit or disconnecting the battery. • The stored contents can be recalled by performing operation in "Recalling the Stored Equalizer Curve" (page 15). • Pressing /RTN when Parametric EQ is adjusted will return to the previous item. • If MultEQ is turned on, the A.SEL button is ineffective. For details, refer to "Turning MultEQ on/off " (page 13). • If no operation is performed for 60 seconds, the unit will return to the normal mode. Adjusting and Storing the Graphic Equalizer Curve You can modify the equalizer settings to create a response curve more appealing to your personal taste. To adjust the graphic equalizer curve, set the EQ mode to Graphic EQ. For details, refer to "Setting EQ mode" (page 14). 1 Press A.SEL to recall the DSP adjust mode. Media Xpander Crossover T.Correction Parametric EQ/Graphic EQ Media Xpander 2 Turn the Rotary encoder to select Graphic EQ mode, and then press / /ENT. 3 Press BAND to select the band to be adjusted. Band1 Band2 Band3 Band4 Band5 Band6 Band7 Band1 Band-1 (63 Hz) / Band-2 (150 Hz) / Band-3 (400 Hz) / Band-4 (1 kHz) / Band-5 (2.5 kHz) / Band-6 (6.3 kHz) / Band-7 (17.5 kHz)