Alpine CDA-9887 Owners Manual - Page 20
Setting the Time Correction Unit, Adjusting and Storing the Time Correction
UPC - 793276711373
View all Alpine CDA-9887 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 20 highlights
Time Difference Table Delay Number 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Distance (cm) 0.0 3.4 6.8 10.2 13.6 17.0 20.4 23.8 27.2 30.6 34.0 37.4 40.8 44.2 47.6 51.0 54.4 57.8 61.2 64.6 68.0 71.4 74.8 78.2 81.6 85.0 88.4 91.8 95.2 98.6 102.0 105.4 108.8 112.2 115.6 119.0 122.4 125.8 129.2 132.6 136.0 139.4 142.8 146.2 149.6 153.0 156.4 159.8 163.2 166.6 170.0 Distance (inch) 0.0 1.3 2.7 4.0 5.4 6.7 8.0 9.4 10.7 12.1 13.4 14.7 16.1 17.4 18.8 20.1 21.4 22.8 24.1 25.5 26.8 28.1 29.5 30.8 32.2 33.5 34.8 36.2 37.5 38.9 40.2 41.5 42.9 44.2 45.6 46.9 48.2 49.6 50.9 52.3 53.6 54.9 56.3 57.6 59.0 60.3 61.6 63.0 64.3 65.7 67.0 Delay Number 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 Distance (cm) 173.4 176.8 180.2 183.6 187.0 190.4 193.8 197.2 200.6 204.0 207.4 210.8 214.2 217.6 221.0 224.4 227.8 231.2 234.6 238.0 241.4 244.8 248.2 251.6 255.0 258.4 261.8 265.2 268.6 272.0 275.4 278.8 282.2 285.6 289.0 292.4 295.8 299.2 302.6 306.0 309.4 312.8 316.2 319.6 323.0 326.4 329.8 333.2 336.6 Distance (inch) 68.3 69.7 71.0 72.4 73.7 75.0 76.4 77.7 79.1 80.4 81.7 83.1 84.4 85.8 87.1 88.4 89.8 91.1 92.5 93.8 95.1 96.5 97.8 99.2 100.5 101.8 103.2 104.5 105.9 107.2 108.5 109.9 111.2 112.6 113.9 115.2 116.6 117.9 119.3 120.6 121.9 123.3 124.6 126.0 127.3 128.6 130.0 131.3 132.7 Setting the Time Correction Unit You can change the unit, (cm or inch) of time correction. 1 Press and hold FUNC./SETUP for at least 2 seconds to setup the Selection mode. 2 Turn the Rotary encoder to select AUDIO mode, and then press / /ENT. Bluetooth GENERAL TUNER* Bluetooth AUDIO DISPLAY * Only when HD Radio/SAT Radio is connected. 3 Turn the Rotary encoder to select T.CORR Parameter mode, and then press / /ENT. 4 Turn the Rotary encoder to select the desired items, and then press / /ENT. T.CORR Parameter T.CORR Parameter (Initial setting) 5 After setting, press and hold FUNC./SETUP for at least 2 seconds to return to normal mode. • Pressing /RTN during the procedure will return to the previous mode. • If no operation is performed for 60 seconds in the SETUP mode, the setting mode is canceled. • Press and hold /ESC for at least 2 seconds, the setting mode is canceled. Adjusting and Storing the Time Correction Before performing the following procedures, refer to "About Time Correction" (page 17). 1 Press A.SEL to recall the DSP adjust mode. Media Xpander Crossover T.Correction Parametric EQ/Graphic EQ Media Xpander 2 Turn the Rotary encoder to select the T.Correction mode, and then press / /ENT. 3 Press BAND to select a speaker to be adjusted. 2.2ch (3WAY) System L-F (Initial setting) (Mid-L) L-SW R-SW R-F L-R R-R (Mid-R) (High-L ) (High-R) L-F (Mid-L) 4.2ch (F/R/Sub-W) System L-F (Initial setting) (Front-L) L-SW R-SW R-F L-R (Front-R) (Rear-L) L-F (Front-L) R-R (Rear-R) 18-EN