Alpine ICS-X7HD Owner's Manual (english) - Page 23

2 Adjust the crossover to your preference. Selecting the Cut-Off Frequency Touch [ ] or [ ] of "Freq.," then select the cut-off frequency. Setting contents: 20 / 25 / 31.5 / 40 / 50 / 63 / 80 (Initial setting) / 100 / 125 / 160 / 200 Hz Adjusting the Slope Touch [ ] or [ ] of "Slope," then adjust the HPF or LPF slope. Setting contents: 0 (Initial setting) / 6 / 12 / 18 / 24 dB/oct Adjusting the Level Touch [ ] or [ ] of "Level," then adjust the HPF or LPF level. Setting contents: -12 to 0 dB (Initial setting: 0) 3 Repeat steps 1 to 2 to make adjustment to the other channels. 4 To store the adjusted setting value, touch and hold [Preset1], [Preset2], or [Preset3]. • Touch [Flat] to initialize all values. • If the Subwoofer setting is "Off," the Subwoofer setting cannot be edited (Refer to page 20). • While adjusting the X-OVER you should consider the frequency response of the connected speakers. Calling the X-OVER adjusted value Calling the pre-set X-OVER adjusted value. Touch [Preset1], [Preset2], or [Preset3] on the XOVER screen. The setting stored in the Preset will be recalled. Adjusting the Parametric Equalizer Curve (Parametric EQ) [Parametric EQ] is selected on the Audio setup menu in step 3. Refer to "Audio Setup Operation" (page 20). You can modify the Equalizer settings to create a response curve more appealing to your personal taste. Setting item: Parametric EQ 1 Adjust the Parametric EQ to your preference. Adjusting the Frequency Touch [ ] or [ ] of "Freq." to adjust the frequency of the selected band. Adjustable frequency bands: 20 Hz to 20 kHz (in 1/3 octave steps) BAND1: 20 Hz~100 Hz (63 Hz) BAND2: 63 Hz~315 Hz (125 Hz) BAND3: 125 Hz~500Hz (250 Hz) BAND4: 250 Hz~1 kHz (500Hz) BAND5: 500 Hz~2 kHz (1 kHz) BAND6: 1 kHz~4 kHz (2 kHz) BAND7: 2 kHz~7.2 kHz (4 kHz) BAND8: 5.8 kHz~12 kHz (8 kHz) BAND9: 9 kHz~20 kHz (16 kHz) Adjusting the Level Touch [ ] or [ ] of "Level" to adjust the level of selected band. Setting contents: -7 to +7 (Initial setting: 0) Setting the Bandwidth Touch [ ] or [ ] of "Q Adjust" to select the bandwidth. Setting contents: 1 (Initial setting) / 2 / 3 2 To adjust another band, repeat step 1, and adjust all bands. 3 To store the adjusted setting value, touch and hold [Preset1], [Preset2], or [Preset3]. • Settings exceeding the frequency of adjacent bands are not available. • While adjusting the Parametric EQ, you should consider the frequency response of the connected speakers. • When the parametric EQ is adjusted, the adjustment for Bass Max EQ becomes ineffective. • When Bass Max EQ is set, the interlinked Parametric EQ settings are also changed. We recommend storing Parametric EQ settings in the Preset in advance. • Touch [Flat] to initialize all values. • The Parametric EQ setting can be configured when Defeat is "Off." Calling the Parametric EQ adjusted value Calling the pre-set Parametric EQ adjusted value. Touch [Preset1], [Preset2], or [Preset3] on the Parametric EQ screen. The setting stored in the Preset will be recalled. Adjusting the Band Touch [Band] to select the band to be adjusted. BAND1 BAND2 ··· BAND8 BAND9 • You can select a band directly by touching the screen. 23-EN