Campbell Scientific CR10 CR10 Measurement and Control - Page 73

SECTION

5.

TELECOMMUNICATIONS

TABLE

5.1-1. Telecommunications Commands

Command

DescriPtion

[F.S.

Area]A

SELECT AREA/STATUS

- lf

1

or 2

does

not precede the A

to

select

the

Final Storage Area,

the

CRl0

will default to

Area

1.

All

subsequent

commands other than A will address the

area

selected.

Datalogger

.

returns Reference; the"DSP location;

the

number

of

filled

Final Storage

locations; Version of

datalogger;

Errors

#1

and #2 where

#1

is

the

number

of

E08's and

#2

is

the

number of overrun

errors

(both are

cleared

by entering 8888A;

#2

is also cleared

at

time

of program

compilation); size

of

total

Memory

in

CR10;

Final Storage Area;

Location of MPTR; and

Checksum. All

in

the following format:

R+xxxxx

Fxxxxx Vxx Exx

xx

Mxx

Ax L+xxxxx

Cxxxx

lf

data

is

stored

while

in

telecommunications,

the A

command

must be

issued

to

update

the

Reference to

the new

DSP.

[no.

of

anays]B

BACK-UP

- MPTR is backed-up the

specified

number

of,,Output

Arrays

(no number defaults

to

1)

and advanced to

the

nearest start of array.

CR10 sends the

Area,

MPTR Location, and

Checksum: Ax

L+xxxxx

Cxxxx

[YR:DAY:HR:MM:SS]C

RESET/SEND

TIME -

lf

time

is

entered the

time is

reset.

lf only

2

colons

are

in the time string,

HR:MM:SS

is

assumed;

3

colons means

DAY:HR:MM:SS.

lf only

the

C

is

entered,

time

is

unaltered. CRlO

returns year, Julian day, hr:min:sec, and

Checksum: Y:xx

Dxxxx

Txx:xx:xx Cxxxx

[no.

of

arrays]D

ASCII

DUMP

-

If necessary,

the

MPTR is advanced

to

start of scan.

CR10 sends

the

number of arrays

specified

(no number defaults

to

1)

or

the

number of arrays between MPTR

and

Reference,

whichever

is

smaller,

CRLF, Location, Checksum.

E

End

call.

Datalogger sends CRLF only.

[no.

of

loc.]F

BINARY DUMP

-

Used

in

TELCOM

(PC208).

See

Appendix

C.

[F.S.

loc.

no.]G

MOVE MPTR - MPTR is moved

to specified FinalStorage

location.

The

location number must be

entered.

CR10 sends

Area,

Location,

and

Checksum: Ax

L+xxxxx Cxxxx

7H

or2718H

REMOTE KEYBOARD

-

CR10 sends

the

prompt ">" and is ready

to

execute standard keyboard

commands

(Section OV3).

[loc.

no.]l

Display/change value

at

lnput Storage

location.

CRl

O

sends the value

stored at the

location. A

new value

and

CR may

then

be

sent.

CR10

sends

checksum.

lf

no new

value

is

sent

(CR only)

the

location value

will

remain

the

same.

3142J

TOGGLE

FLAGS AND

SET

UP FOR K COMMAND

-

Used

in

the

Monitor Mode and with

the

Heads Up

Display.

See Appendix C

for

details.

5-3

Campbell Scientific CR10 CR10 Measurement and Control - Page 73

Area]A

Page 73 highlights