Canon Color imageCLASS MF9280Cdn imageCLASS MF9280Cdn/MF9220Cdn Starter Guide - Page 33

You selected <Do Not Perform Full Corr.> =Quick, Correction, go to Set Up, Network Connection

Get Canon Color imageCLASS MF9280Cdn PDF manuals and user guides View all Canon Color imageCLASS MF9280Cdn manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

1 Settings Necessary to Use the Machines Functions 3 Use or (Scroll Wheel) to select or , then press [OK]. 4 Make sure the following screen is displayed on the display, then press [OK] to print the first test page. - It is recommended that you select . - It takes approximately five minutes to perform the full correction. - For the full correction, the machine performs the correction twice and two test prints are output by the machine for the each correction. ● You selected (=Quick Correction) Make sure the following screen is displayed on the display, then press [OK] to start the quick correction. (It takes approximately two and a half minutes to perform the quick correction.) If an error message appears: If you set in of , an error message will appear. If this is the case, follow the instructions below. 1. P ress the right Any key to select and return to the screen in step 3. 2. L oad LTR or A4 plain paper into the stack bypass tray and set the paper size and type. 3. U se or (Scroll Wheel) to select . 5 Place the first test print on the platen glass. Recalibrations are made internally without outputting any test prints. After finishing the quick correction, go to "Set Up Network Connection," on p. 33. Place the test print face down on the platen glass, with the black bands along the top left edge of the platen glass. Stack approximately 20 sheets of blank paper on top of the test print for a more precise gradation correction. 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
31
1 Settings Necessary to Use the Machines Functions
3
Use [
▼
], [
▲
] or
(Scroll Wheel) to
select<Perform Full Correction> or <Do Not
Perform Full Corr.>, then press [
OK
].
It is recommended that you select <Perform Full
Correction>.
It takes approximately five minutes to perform the full
correction.
For the full correction, the machine performs the
correction twice and two test prints are output by the
machine for the each correction.
You selected <Do Not Perform Full Corr.> (=Quick
Correction)
Make sure the following screen is displayed on the display, then press [
OK
] to
start the quick correction. (It takes approximately two and a half minutes to
perform the quick correction.)
Recalibrations are made internally without outputting any
test prints.
After finishing the quick correction,
go to “Set Up
Network Connection,”on p. 33
.
–
–
–
●
4
Make sure the following screen is displayed on
the display, then press [
OK
] to print the first test
page.
If an error message appears:
If you set <Color> in <Paper Type> of <Paper Settings>, an
error message will appear. If this is the case, follow the
instructions below.
1.
Press the right Any key to select <Done> and return to
the screen in step 3.
2.
Load LTR or A4 plain paper into the stack bypass tray and
set the paper size and type.
3.
Use [
▼
], [
▲
] or
(Scroll Wheel) to select
<Full Correction>.
5
Place the first test print on the platen glass.
Place the test print face down on the platen glass, with the
black bands along the top left edge of the platen glass.
Stack approximately 20 sheets of blank paper on top of the
test print for a more precise gradation correction.