Canon DR-7080C User Manual - Page 67

Using the Count Only Mode

Get Canon DR-7080C PDF manuals and user guides View all Canon DR-7080C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

4.4 Other Scanning Techniques Using the Count Only Mode In the Count Only Mode, document pages are sent through the feeder in order to count them. The document is not scanned. You can perform Count Only Mode operations on the scanner, without using your computer. 1 Use the user modes to enter the scanner's Count Only Mode. (See "How to Set the User Modes," on p. 72.) This causes the Start key lamp to light green. 2 Load the document into the feeder, and then press the [Start] key. 4 This sends the pages of the document through the feeder and counts them. 3 After all of the document pages are fed, exit the Count Only Mode. (See "How to Set the User Modes," on p. 72.) To clear the page count from the display panel, hold down the [Stop] key for approximately two seconds. 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
63
4
Using the Count Only Mode
In the Count Only Mode, document pages are sent through the feeder in order to
count them. The document is not scanned. You can perform Count Only Mode
operations on the scanner, without using your computer.
1
Use the user modes to enter the scanner's Count Only Mode.
(See “How to Set the User Modes,” on p. 72.)
This causes the Start key lamp to light green.
2
Load the document into the feeder, and then press the [Start] key.
This sends the pages of the document through the feeder and counts them.
3
After all of the document pages are fed, exit the Count Only Mode.
(See “How to Set the User Modes,” on p. 72.)
To clear the page count from the display panel, hold down the [Stop] key
for approximately two seconds.
4.4
Other Scanning Techniques