Home » Cisco Manuals » Hubs & Switches » Cisco SRW2024P » Manual Viewer

Cisco SRW2024P User Guide - Page 66

Via TFTP, Via HTTP, Backup - firmware download

UPC - 745883571000

View all Cisco SRW2024P manuals

Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

Chapter 5 Admin > Save Configuration Advanced Configuration Admin > Firmware Upgrade After you download a new image file, the device should be rebooted. If you are downloading a new boot image, please follow these steps: 1. Download the new boot code. DO NOT RESET THE DEVICE! 2. Download the new software image. 3. Reset the device now. Admin > Save Configuration Via TFTP Upgrade Select this option to upgrade the switch from a file located on a TFTP server. •• TFTP Server The TFTP Server IP Address that contains the source file to upgrade from. •• Source File Specifies the name of the upgrade file on the TFTP Server. Backup To backup the switch configuration via TFTP, enter the TFTP server address. •• TFTP Server Specifies the TFTP Server IP Address to which the Configuration file will be saved. •• Destination File Specifies the name of the configuration file. The default is StartupCfg.cfg. Via HTTP This HTTP Firmware Upgrade screen is used for saving configuration information using your Web browser. Upgrade Select this option to upgrade the switch from a file on the local hard drive. •• Source File Type in the name and path of the file or Browse to locate the upgrade file. Backup •• Proceed The Proceed button is used to backup the configuration to the local hard drive. NOTE: When downloading a configuration file, be sure that it is a valid configuration file. If you have edited the file, ensure that only valid entries have been configured. Admin > Firmware Upgrade The Firmware Upgrade screen contains the following fields: via TFTP Defines the upgrade through a TFTP Server. via HTTP Allows you to upgrade the firmware using your Web browser. Upgrade Defines the screen functionality as a Firmware upgrade. Backup Defines the screen functionality as a Firmware backup. TFTP Server IP Address Specifies the TFTP Server IP Address from which files are downloaded. Source File Name Specifies the file to be downloaded. Destination File name Specifies the destination file type to which the file is downloaded. The possible field values are: Software Image Downloads the Image file. Boot Code Downloads the Boot file. WebView Switches 59

Section	Page
Chapter 1: Introduction	8
Chapter 2: Product Overview	9
SRW2048	9
Front Panel	9
LEDs	9
Back Panel	9
SRW2024	10
Front Panel	10
LEDs	10
Back Panel	10
SRW2016	11
Front Panel	11
LEDs	11
The Back Panel	11
SRW248G4	12
Front Panel	12
LEDs	12
Back Panel	12
SRW224G4	13
Front Panel	13
LEDs	13
Back Panel	13
Chapter 3: Connecting the Switch	15
Overview	15
Placement Options	15
Desktop Placement	15
Rack-Mount Placement	15
Hardware Installation	16
Configuring the Switch	16
Chapter 4: Configuration Using the Console Interface	17
Overview	17
Configuring the HyperTerminal Application	17
Connecting to the Switch through a Telnet Session	17
Configuring the Switch through the Console Interface	18
Switch Main Menu	18
System Configuration Menu	18
Port Status	25
Port Configuration	26
Help	26
Chapter 5: Advanced Configuration	27
Overview	27
Accessing the Web-based Utility	27
Setup > Summary	27
Device Information	27
System Information	28
Setup > Network Settings	28
Identification	28
IP Configuration	28
Setup > Time	29
Set Time	29
Local Time	29
Daylight Saving	29
SNTP Servers	29
Setup > Green Ethernet	30
Port Management > Port Settings	30
Port Settings > Port Configuration	31
Port Management > Link Aggregation	32
Link Aggregation > Detail	32
Port Management > LACP	33
VLAN Management > Create VLAN	33
Single VLAN	33
VLAN Range	33
VLAN Table	33
VLAN Management > Port Setting	34
VLAN Management > Ports to VLAN	34
VLAN Management > VLAN to Ports	35
VLAN Management > GVRP	35
Statistics > RMON Statistics	36
Statistics > RMON History	37
Log Table	37
RMON History	37
Statistics > RMON Alarm	38
Statistics > RMON Events	39
Add Event	39
RMON Events Log	39
Statistics > Port Utilization	39
Statistics > 802.1x Statistics	40
Statistics > GVRP Statistics	40
ACL > IP Based ACL	41
ACL > MAC Based ACL	42
Security > ACL Binding	43
Security > RADIUS	43
Security > TACACS+	44
Security > 802.1x Settings	44
802.1x Settings > Setting Timer	45
Security > Port Security	45
Security > Multiple Hosts	46
Security > Storm Control	47
QoS	47
QoS > CoS Settings	47
CoS Default	48
QoS > Queue Settings	48
QoS > DSCP Settings	48
QoS > Bandwidth	48
QoS > Basic Mode	49
QoS > Advanced Mode	49
Advanced Mode > Out of Profile DSCP	49
Advanced Mode > Policy Name	50
Advanced Mode > New Class Map	50
Advanced Mode > New Aggregate Policer	50
Spanning Tree	50
Spanning Tree > STP Status	51
Spanning Tree > Global STP	51
Global Setting	51
Bridge Settings	52
Spanning Tree > STP Port Settings	52
Spanning Tree > RSTP Port Settings	53
Spanning Tree > MSTP Properties	54
Spanning Tree > MSTP Instance Settings	55
Spanning Tree > MSTP Interface Settings	55
Multicast > IGMP Snooping	56
Multicast > Bridge Multicast	57
Multicast > Bridge Multicast Forward All	57
SNMP > Global Parameters	58
SNMP > Views	58
SNMP > Group Profile	59
SNMP > Group Membership	59
SNMP > Communities	60
Base Table	61
Advanced Table	61
SNMP > Notification Filter	61
SNMP > Notification Recipient	62
Admin > User Authentication	62
Admin > Jumbo Frames	63
Admin > Static Address	63
Query	63
Admin > Dynamic Address	64
Query	64
Admin > Logging	64
Admin > Port Mirroring	65
Admin > Cable Test	65
Admin > Save Configuration	66
Via TFTP	66
Via HTTP	66
Backup	66
Admin > Firmware Upgrade	66
Admin > Reboot	67
Admin > Factory Defaults	67
Admin > Server Logs	67
Admin > Memory Logs	68
Admin > Flash Logs	68
Appendix A: About Gigabit Ethernet and Fiber Optic Cabling	69
Gigabit Ethernet	69
Fiber Optic Cabling	69
Appendix B: Windows Help	70
TCP/IP	70
Shared Resources	70
Network Neighborhood/My Network Places	70
Appendix C: Downloading using Xmodem	71
Startup Menu Procedures	71
Appendix D: Glossary	73
Appendix E: Specifications	77
Appendix F: Warranty Information	82
Limited Warranty	82
Exclusions and Limitations	82
Obtaining Warranty Service	82
Technical Support	83
Appendix G: Regulatory Information	84
FCC Statement	84
Safety Notices	84
Industry Canada Statement	84
Avis d’Industrie Canada	84
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE)	85
Appendix H: Software License Agreement	89
Software in Linksys Products:	89
Software Licenses:	89
Schedule 1 Linksys Software License Agreement	89
Schedule 2	90
Schedule 3	93

Match case Limit results 1 per page

Chapter 5

Advanced Configuration

WebView Switches

Admin > Save Configuration

Via TFTP

Upgrade

Select this option to upgrade the switch from a

file located on a TFTP server.

TFTP Server

•

The TFTP Server IP Address that contains

the source file to upgrade from.

Source File

•

Specifies the name of the upgrade file on

the TFTP Server.

Backup

To backup the switch configuration via TFTP,

enter the TFTP server address.

TFTP Server

•

Specifies the TFTP Server IP Address to

which the Configuration file will be saved.

Destination

File

•

Specifies

the

name

the

configuration file. The default is

StartupCfg.cfg

Via HTTP

This

HTTP Firmware Upgrade

screen is used for saving

configuration information using your Web browser.

Upgrade

Select this option to upgrade the switch from a

file on the local hard drive.

Source File

•

Type in the name and path of the file or

Browse to locate the upgrade file.

Backup

Proceed

•

The

Proceed

button is used to backup the

configuration to the local hard drive.

NOTE:

When downloading a configuration file,

be sure that it is a valid configuration file. If

you have edited the file, ensure that only valid

entries have been configured.

Admin > Firmware Upgrade

After you download a new image file, the device should

be rebooted. If you are downloading a new boot image,

please follow these steps:

Download the new boot code. DO NOT RESET THE

DEVICE!

Download the new software image.

Reset the device now.

Admin > Firmware Upgrade

The

Firmware Upgrade

screen contains the following

fields:

via TFTP

Defines the upgrade through a TFTP Server.

via HTTP

Allows you to upgrade the firmware using your

Web browser.

Upgrade

Defines the screen functionality as a Firmware

upgrade.

Backup

Defines the screen functionality as a Firmware

backup.

TFTP Server IP Address

Specifies the TFTP Server IP

Address from which files are downloaded.

Source File Name

Specifies the file to be downloaded.

Destination File name

Specifies the destination file type

to which the file is downloaded. The possible field values

are:

Software Image

Downloads the Image file.

Boot Code

Downloads the Boot file.