Home » Compaq Manuals » Desktops » Compaq dx7500 » Manual Viewer

Compaq dx7500 Service Reference Guide: HP Compaq dx7500 Business PC - Page 80

Installing a Drive into the 3.5-inch External Drive Bay

Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

Installing a Drive into the 3.5-inch External Drive Bay The 3.5-inch external drive bay on the front of the computer can be configured with a media card reader or a diskette drive. 1. Prepare the computer for disassembly (Preparation for Disassembly on page 47). 2. Remove the access panel (Access Panel on page 48). 3. Remove the front bezel (Front Bezel on page 49). 4. If you are installing a diskette drive or media card reader in a bay covered by a bezel blank, remove the front bezel then remove the bezel blank. 5. If you are adding a drive to an empty drive bay for the first time, you must remove the knockout plate from the bay. To do so, insert a flat screwdriver into the knockout plate slot and rotate the screwdriver to break the knockout plate out of the chassis. Discard the knockout plate. 6. If the new drive has screws installed on the sides of the drive, remove them before inserting the drive into the chassis. 7. Slide the drive in through the front of the chassis (1) until the screw holes on the drive are aligned with the screw holes on the drive cage and install the two M3 metric retainer screws (2) as shown in the illustration below. NOTE: Extra drive retainer screws are provided on the interior of the front bezel if needed. The M3 metric retainer screws for diskette drives or media card readers are black. Refer to Installing Additional Drives on page 63 for an illustration of the retainer screws location. Figure 7-24 Installing a 3.5-inch Device (Media Card Reader Shown) 8. Connect the appropriate drive cables: a. If installing a diskette drive, connect the power and data cables to the rear of the drive and connect the other end of the data cable to the connector on the system board labeled FLOPPY. b. If installing a media card reader, connect the USB cable from the media card reader to the USB connector on the system board labeled F_USB2. 70 Chapter 7 Removal and Replacement Procedures Microtower (MT) Chassis

Section	Page
Installing and Customizing the Software	11
Installing the Operating System	11
Installing or Upgrading Device Drivers	11
HP Backup and Recovery Manager	11
Computer Setup (F10) Utility	13
Computer Setup (F10) Utilities	13
Using Computer Setup (F10) Utilities	13
Computer Setup—Main	14
Computer Setup—Advanced	15
Computer Setup—Power	16
Computer Setup—Boot	17
Computer Setup—Exit	17
Recovering the Configuration Settings	18
Computer Diagnostic Features	19
HP Insight Diagnostics	19
Accessing HP Insight Diagnostics	19
Survey Tab	20
Test Tab	21
Status Tab	21
Log Tab	22
Help Tab	22
Saving and Printing Information in HP Insight Diagnostics	23
Downloading the Latest Version of HP Insight Diagnostics	23
Protecting the Software	23
HP Backup and Recovery Manager	24
Desktop Management	25
Initial Configuration and Deployment	25
HP Software Agent	26
Altiris Deployment Solution Agent	26
Remote System Installation	27
Software Updating and Management	27
HP Client Management Interface	27
HP SoftPaq Download Manager	28
HP System Software Manager	28
HP ProtectTools Security Manager	29
HP Client Automation Starter and Standard Editions	29
HP Client Automation Enterprise Edition	30
HP Client Manager from Symantec	30
Altiris Client Management Suite	31
HP Client Catalog for Microsoft System Center & SMS Products	31
HP Backup and Recovery Manager	31
Verdiem Surveyor	32
HP Proactive Change Notification	32
Subscriber’s Choice	32
Retired Solutions	33
ROM Flash	33
Remote ROM Flash	33
HPQFlash	33
Boot Block Emergency Recovery Mode	33
Replicating the Setup	34
Copying to Single Computer	34
Copying to Multiple Computers	35
Creating a Bootable Device	36
Supported USB Flash Media Device	36
Unsupported USB Flash Media Device	37
Dual-State Power Button	39
HP Web Site Support	39
Industry Standards	40
Asset Tracking and Security	40
Password Security	41
Establishing a Supervisor Password Using Computer Setup	41
Entering a Supervisor Password or User password	42
Changing a Supervisor or User password	42
Deleting a Supervisor or User Password	43
National Keyboard Delimiter Characters	43
Clearing Passwords	43
Cable Lock Provision	44
Fault Notification and Recovery	44
Drive Protection System	44
Surge-Tolerant Power Supply	44
Thermal Sensor	44
Serial ATA (SATA) Drive Guidelines and Features	45
SATA Hard Drives	45
SATA Hard Drive Cables	45
SATA Data Cable	45
SMART ATA Drives	46
Hard Drive Capacities	46
Identifying the Chassis, Routine Care, and Disassembly Preparation	47
Chassis Designations	47
Microtower (MT)	47
Small Form Factor (SFF)	48
Electrostatic Discharge Information	48
Generating Static	48
Preventing Electrostatic Damage to Equipment	49
Personal Grounding Methods and Equipment	49
Grounding the Work Area	50
Recommended Materials and Equipment	50
Operating Guidelines	51
Routine Care	52
General Cleaning Safety Precautions	52
Cleaning the Computer Case	52
Cleaning the Keyboard	52
Cleaning the Monitor	53
Cleaning the Mouse	53
Service Considerations	53
Power Supply Fan	53
Tools and Software Requirements	53
Screws	54
Cables and Connectors	54
Hard Drives	54
Lithium Coin Cell Battery	54
Removal and Replacement Procedures Microtower (MT) Chassis	56
Serial Number Location	56
Preparation for Disassembly	57
Access Panel	58
Front Bezel	59
Bezel Blanks	60
Memory	61
DDR2-SDRAM DIMMs	61
Populating DIMM Sockets	62
Installing Memory Modules	63
Expansion Cards	65
Cable Management	69
Cable Connections	71
Drives	72
Drive Positions	72
Installing Additional Drives	73
System Board Drive Connections	74
Removing an Optical Drive	75
Installing an Optical Drive into the 5.25-inch Drive Bay	76
Removing an External 3.5-inch Drive	78
Installing a Drive into the 3.5-inch External Drive Bay	80
Removing an Internal 3.5-inch Hard Drive	81
Installing an Internal 3.5-inch Hard Drive	84
Front I/O and USB Panel Housing Assembly	87
Power Switch/LED Assembly	88
Speaker	89
System Fan	90
Heatsink assembly	91
Processor	92
Power Supply	93
System Board	94
Battery	95
Type 1 Battery Holder	96
Type 2 Battery Holder	96
Type 3 Battery Holder	97
Installing a Security Lock	98
Cable Lock	98
Padlock	98
HP Business PC Security Lock	99
Removal and Replacement Procedures Small Form Factor (SFF) Chassis	101
Preparation for Disassembly	101
Access Panel	102
Front Bezel	103
Bezel Blanks	104
Cable Management	105
Cable Connections	106
Drives	107
Drive Positions	107
Installing Additional Drives	108
System Board Drive Connections	110
Removing an Optical Drive	111
Installing an Optical Drive into the 5.25-inch Drive Bay	113
Removing an External 3.5-inch Drive	115
Installing a Drive into the 3.5-inch External Drive Bay	118
Removing an Internal 3.5-inch Hard Drive	121
Installing an Internal 3.5-inch Hard Drive	123
Memory	125
DDR2-SDRAM DIMMs	125
Populating DIMM Sockets	126
Installing DIMMs	127
Removing or Installing an Expansion Card	130
Plastic Wire/Cable Fastener and Clips	135
Front I/O Device	136
Power Switch Assembly	137
Speaker	138
Heatsink	139
Processor	140
Power Supply	141
System Board	142
Battery	144
Type 1 Battery Holder	145
Type 2 Battery Holder	145
Type 3 Battery Holder	146
Installing a Security Lock	147
Cable Lock	147
Padlock	147
HP Business PC Security Lock	148
Connector Pin Assignments	150
Keyboard	150
Mouse	150
USB	151
Microphone	151
Headphone	151
Line-in Audio	151
Line-out Audio	151
Monitor	152
24-Pin Power	152
PCI Express	153
PCI Express	154
4-Pin Power (for CPU)	155
DVI Connector	155
SPDIF	155
Power Cord Set Requirements	156
General Requirements	156
Japanese Power Cord Requirements	156
Country-Specific Requirements	157
Troubleshooting Without Diagnostics	158
Safety and Comfort	158
Before You Call for Technical Support	158
Helpful Hints	159
Solving General Problems	161
Solving Power Problems	164
Solving Diskette Problems	165
Solving Hard Drive Problems	167
Solving Media Card Reader Problems	169
Solving Display Problems	170
Solving Audio Problems	174
Solving Printer Problems	175
Solving Keyboard and Mouse Problems	176
Solving Hardware Installation Problems	178
Solving Network Problems	180
Solving Memory Problems	182
Solving CD-ROM and DVD Problems	183
Solving USB Flash Drive Problems	185
Solving Front Panel Component Problems	186
Solving Internet Access Problems	187
Solving Software Problems	189
Interpreting POST Audible Codes	190
Resetting the Password Jumper	191
Resetting the CMOS Jumper	192
Contacting Customer Support	193
Specifications	194
Minitower	194
Small Form Factor	195

Match case Limit results 1 per page

Installing a Drive into the 3.5-inch External Drive Bay

The 3.5-inch external drive bay on the front of the computer can be configured with a media card reader

or a diskette drive.

Prepare the computer for disassembly (

Preparation for Disassembly

on page

Remove the access panel (

Access Panel

on page

Remove the front bezel (

Front Bezel

on page

If you are installing a diskette drive or media card reader in a bay covered by a bezel blank, remove

the front bezel then remove the bezel blank.

If you are adding a drive to an empty drive bay for the first time, you must remove the knockout

plate from the bay. To do so, insert a flat screwdriver into the knockout plate slot and rotate the

screwdriver to break the knockout plate out of the chassis. Discard the knockout plate.

If the new drive has screws installed on the sides of the drive, remove them before inserting the

drive into the chassis.

Slide the drive in through the front of the chassis

(1)

until the screw holes on the drive are aligned

with the screw holes on the drive cage and install the two M3 metric retainer screws

(2)

as shown

in the illustration below.

NOTE:

Extra drive retainer screws are provided on the interior of the front bezel if needed. The

M3 metric retainer screws for diskette drives or media card readers are black. Refer to

Installing

Additional Drives

on page

for an illustration of the retainer screws location.

Figure 7-24

Installing a 3.5-inch Device (Media Card Reader Shown)

Connect the appropriate drive cables:

If installing a diskette drive, connect the power and data cables to the rear of the drive and

connect the other end of the data cable to the connector on the system board labeled FLOPPY.

If installing a media card reader, connect the USB cable from the media card reader to the

USB connector on the system board labeled F_USB2.

Chapter 7

Removal and Replacement Procedures Microtower (MT) Chassis