Craftsman 22901 Instruction Manual - Page 18

See

Get Craftsman 22901 - Professional 17 in. Drill Press PDF manuals and user guides View all Craftsman 22901 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

FLEXUBLE LAMP To reduce the risk of fire, use 40 watt or less, 120 volt, reflector track-type Hight buib (not supplied), DO NOT use a standard househoid Hight buib, The reflector tracktype Hightbuib shouid not extend bellow the iamp shade, Figure 9-1 B A TABLE OPERATION Figure 10-1 B C ©© 1, To raise or lower the table (A) on the column (B), loosen the table lock handle (C), See Figure 10-1 and 10-2, Figure 10-2 A The flexible lamp (A) operates independently of the drill press and has its own power cord, To turn the lamp ON and OFF, rotate the switch (B) in the clockwise direction only, See Figure 9-1, CAUTION: The flexible lamp housing wiii remain hot for a few minutes after turning it OFR Avoid contact with housing until it is cook E 2, Turn the table raising and lowering handle (D) clockwise to raise the table and counter-clockwise to lower the table, See Figure10-2, 3, After the table is at the desired height, tighten the table height lock handle, NOTE: Always raise (rather than lower) the table to the final position to allow the gears to mesh and prevent slippage, 4, The table (A) can be rotated 360 degrees by loosening the table rotation lock handle (E) and rotating the table to the desired position, and tightening the table clamp, See Figure 10-2, NOTE: For thru-drilling operations, make sure the table center hob is aligned with the drill bit, 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
FLEXUBLE
LAMP
To reduce the risk of fire, use 40 watt or less, 120 volt,
reflector track-type
Hight buib (not supplied),
DO NOT
use a standard
househoid
Hight buib, The reflector track-
type Hightbuib shouid not extend bellow the iamp shade,
Figure
9-1
B
A
©
©
The flexible lamp (A) operates
independently
of the drill
press and has its own power cord, To turn the lamp ON
and OFF, rotate the switch (B) in the clockwise
direction
only,
See Figure 9-1,
CAUTION:
The flexible lamp housing wiii remain
hot for
a few minutes after turning it OFR
Avoid contact with
housing until it is cook
TABLE
OPERATION
Figure
10-1
B
C
1,
To raise or lower the table (A) on the column
(B),
loosen the table lock handle (C),
See Figure
10-1
and 10-2,
Figure
10-2
A
E
18
2,
Turn the table raising and lowering
handle (D)
clockwise
to raise the table and counter-clockwise
to lower the table,
See Figure10-2,
3,
After the table is at the desired
height, tighten the
table height lock handle,
NOTE: Always
raise (rather than lower) the table to the
final position
to allow the gears to mesh and prevent
slippage,
4,
The table (A) can be rotated 360 degrees by loos-
ening the table rotation
lock handle
(E) and rotating
the table to the desired position, and tightening
the
table clamp,
See Figure 10-2,
NOTE:
For thru-drilling
operations,
make sure the table
center hob
is aligned with the drill bit,