D-Link DSS-200G-28MP Product Manual - Page 119

PD Alive

Get D-Link DSS-200G-28MP PDF manuals and user guides View all D-Link DSS-200G-28MP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 119 highlights

D-Link DSS-200G MP/MPP series Switch User Manual PD Alive This window is used to configure the PD Alive function for PDs connected to the PoE ports. The ping function via ICMP requests is used to check if PDs, connected to the PoE ports, are active or not. When PDs appear to be inactive, the specified action (Reset, Notify, or Both) will be taken. To view the following window, click on the PD Alive Configuration to enter the navigation menu: Figure 5-11 PD-Alive Window The fields that can be configured are described below: Parameter Description From Port / To Port Select the appropriate port range used for the configuration here. PD Alive State Select to enable or disable the PD Alive function on the specified port(s). Note that a port's PD Alive state cannot be disabled if the DIP Switch on the front panel has been turned on. PD IP Address Enter the IP address of the PD here. Pool interval (10-300) Enter the pool interval here. This is the interval between ping messages from the system to PDs connected to the PoE port(s). The range is from 10 to 300 seconds. Retry Count (0-5) Enter the retry count here. This is the amount of ping messages that will be sent (at each interval) when PDs are not responding. The range is from 1 to 5. Wait Time (30-300) Action Enter the waiting time here. This is how long the system will wait before sending ping messages to the PD connected to the PoE port after a 'Reset' action was taken. The range is from 30 to 300 seconds. Select the action that will be taken here. Options to choose from are Reboot, Notify, and Both. Reboot - Specifies to reset the PoE port state (turn PoE off and on). Notify - Specifies to send logs and traps to notify the administrator. Both - Specifies to send logs and traps to notify the administrator and to reset the PoE port state (turn PoE off and on). 114

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
D-Link DSS-200G MP/MPP series Switch User Manual
114
PD Alive
This window is used to configure the PD Alive function for PDs connected to the PoE ports. The
ping function via ICMP requests is used to check if PDs, connected to the PoE ports, are active or
not. When PDs appear to be inactive, the specified action (Reset, Notify, or Both) will be taken.
To view the following window, click on the
PD Alive Configuration
to enter the navigation menu:
Figure 5-11 PD-Alive Window
The fields that can be configured are described below:
Parameter
Description
From Port / To Port
Select the appropriate port range used for the configuration here.
PD Alive State
Select to enable or disable the PD Alive function on the specified
port(s). Note that a port
’
s PD Alive state cannot be disabled if the DIP
Switch on the front panel has been turned on.
PD IP Address
Enter the IP address of the PD here.
Pool interval (10-300)
Enter the pool interval here. This is the interval between ping messages
from the system to PDs connected to the PoE port(s). The range is
from 10 to 300 seconds.
Retry Count (0-5)
Enter the retry count here. This is the amount of ping messages that
will be sent (at each interval) when PDs are not responding. The range
is from 1 to 5.
Wait Time (30-300)
Enter the waiting time here. This is how long the system will wait before
sending ping messages to the PD connected to the PoE port after a
'Reset' action was taken. The range is from 30 to 300 seconds.
Action
Select the action that will be taken here. Options to choose from are
Reboot
,
Notify
, and
Both
.
Reboot
- Specifies to reset the PoE port state (turn PoE off and on).
Notify
- Specifies to send logs and traps to notify the administrator.
Both
- Specifies to send logs and traps to notify the administrator and
to reset the PoE port state (turn PoE off and on).