Dell Dimension 4300S Dell Dimension 4300S Owner's Manual - Page 69

Close the computer cover see

Get Dell Dimension 4300S PDF manuals and user guides View all Dell Dimension 4300S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

NOTICE: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly or cause damage to the equipment. 15 Close the computer cover (see page 71). 16 Connect your computer and devices to their electrical outlets, and turn them on. NOTICE: To connect a network cable, first plug the cable in to the network wall jack and then plug it in to the computer. 17 Install any drivers required for the card as described in the card documentation. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions listed in "When Working Inside Your Computer" on page 12. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the cover. You can increase your computer memory by installing memory modules on the system board. For information on the type of memory supported by your computer, see "Memory type" under "Memory" on page 75. 1 Shut down the computer (see page 22). 2 Turn off any attached devices and disconnect them from their electrical outlets. NOTICE: To disconnect a network cable, first unplug the cable from your computer and then unplug it from the network wall jack. 3 Disconnect the computer power cable from the wall outlet, and then press the power button to ground the system board. 4 Remove the computer stand, if attached (see page 16). 5 Open the computer cover (see page 61). HINT: Memory purchased from Dell is covered under your computer warranty. Adding Parts 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
Adding Parts
69
NOTICE:
Do not route card cables over or behind the cards. Cables routed
over the cards can prevent the computer cover from closing properly or cause
damage to the equipment.
15
Close the computer cover (see page 71).
16
Connect your computer and devices to their electrical outlets, and
turn them on.
NOTICE:
To connect a network cable, first plug the cable in to the network
wall jack and then plug it in to the computer.
17
Install any drivers required for the card as described in the card
documentation.
CAUTION:
Before you begin any of the procedures in this section,
follow the safety instructions listed in "When Working Inside Your
Computer" on page 12.
CAUTION:
To guard against electrical shock, always unplug your
computer from the electrical outlet before opening the cover.
You can increase your computer memory by installing memory modules on
the system board. For information on the type of memory supported by your
computer, see "Memory type" under "Memory" on page 75.
HINT:
Memory
purchased from Dell is
covered under your
computer warranty.
1
Shut down the computer (see page 22).
2
Turn off any attached devices and disconnect them from their
electrical outlets.
NOTICE:
To disconnect a network cable, first unplug the cable from your
computer and then unplug it from the network wall jack.
3
Disconnect the computer power cable from the wall outlet, and then
press the power button to ground the system board.
4
Remove the computer stand, if attached (see page 16).
5
Open the computer cover (see page 61).