Dell Dimension 4300S Dell Dimension 4300S Owner's Manual - Page 71

My Computer, Properties, General - ram

Get Dell Dimension 4300S PDF manuals and user guides View all Dell Dimension 4300S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

9 Insert the module straight down into the connector, ensuring that it fits into the vertical guides at each end of the connector. Press firmly on the ends of the module until it snaps into place. If you insert the module correctly, the securing clips snap into the cutouts at each end of the module. 10 Close the computer cover (see page 71). 11 Connect your computer and devices to their electrical outlets, and turn them on. NOTICE: To connect a network cable, first plug the cable in to the network wall jack and then plug it in to the computer. 12 Right-click the My Computer icon and then click Properties. 13 Click the General tab. 14 To verify that the memory is installed correctly, check the amount of memory (RAM) listed. 1 Ensure that all cables are connected, and fold cables out of the way. Make sure cables are not routed over the drive cage-they will prevent the cover from closing properly. 2 Ensure that no tools or extra parts are left inside the computer. 3 Pivot the cover down and ensure that the release buttons click into place. 4 Attach the computer stand, if desired (see page 16). NOTICE: To connect a network cable, first plug the cable in to the network wall jack and then plug it in to the computer. 5 Connect your computer and devices to their electrical outlets, and turn them on. Adding Parts 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
Adding Parts
71
9
Insert the module straight down into the connector, ensuring that it
fits into the vertical guides at each end of the connector. Press firmly
on the ends of the module until it snaps into place.
If you insert the module correctly, the securing clips snap into the
cutouts at each end of the module.
10
Close the computer cover (see page 71).
11
Connect your computer and devices to their electrical outlets, and
turn them on.
NOTICE:
To connect a network cable, first plug the cable in to the network
wall jack and then plug it in to the computer.
12
Right-click the
My Computer
icon and then click
Properties
.
13
Click the
General
tab.
14
To verify that the memory is installed correctly, check the amount of
memory (RAM) listed.
1
Ensure that all cables are connected, and fold cables out of the way.
Make sure cables are not routed over the drive cage—they will prevent
the cover from closing properly.
2
Ensure that no tools or extra parts are left inside the computer.
3
Pivot the cover down and ensure that the release buttons click into
place.
4
Attach the computer stand, if desired (see page 16).
NOTICE:
To connect a network cable, first plug the cable in to the network
wall jack and then plug it in to the computer.
5
Connect your computer and devices to their electrical outlets, and
turn them on.