Dell PowerEdge MX7000 EMC OpenManage Enterprise-Modular Edition Version 1.10.2 - Page 51

Viewing compute hardware, Viewing compute firmware

Get Dell PowerEdge MX7000 PDF manuals and user guides View all Dell PowerEdge MX7000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

• When you remove a compute sled, containing an HBA 330 controller with shared mappings, and replace it with a compute sled containing a PERC controller, the sled is checked to ensure that no shared mappings exist. If shared mappings exist, a message is displayed on the Devices > Compute > Overview page for the compute sled, prompting you to clear the mapping. The compute sled is turned off. • When you remove a compute sled containing a PERC controller with mappings, and replace it with a new compute sled having an HBA 330 controller with a different service tag, a message is displayed on the Devices > Compute > Overview page for the compute sled, prompting you to clear or accept the mapping. However, the compute sled is turned on in this scenario. The following flowchart and table illustrate the behavior of OME-Modular and the LCD panel on the chassis when the compute sled is replaced: Figure 1. Compute sled replacement-flowchart Table 17. Compute sled replacement - Behavior of OME-Modular and LCD panel OME-Modular behavior LCD behavior Case 1 Enables users to clear all mappings to the compute sled. Enables users to clear all mappings to the compute sled. Case 2 Enables users to clear or retain all mappings Enables users to clear or retain all mappings to the compute sled. to the compute sled. Viewing compute hardware You can view the details of the hardware components that are installed in the compute sled, on the compute Hardware page. The hardware components include processor, storage controller, and FRU. The deployment and configuration jobs on the compute sled are performed only for the first time, if the profile and sled device ID are unchanged. If the sled is removed and reinserted, the deployment and configuration job is not performed. This condition is applicable to the Edit Profile task too. NOTE: If the storage controller cards are absent in iDRAC, the storage enclosure details are not displayed on the Compute > View Details > Hardware > Storage Enclosure page. Viewing compute firmware You can view the firmware list for the compute in the compute Firmware page. Click Devices > Compute > View Details > Firmware. The details include name of the device or component, impact assessment, current version, and baseline version. You can perform the following tasks on the Firmware page: Managing compute sleds 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
•
When you remove a compute sled, containing an HBA 330 controller with shared mappings, and replace it with a compute sled
containing a PERC controller, the sled is checked to ensure that no shared mappings exist. If shared mappings exist, a message is
displayed on the
Devices
>
Compute
>
Overview
page for the compute sled, prompting you to clear the mapping. The compute sled
is turned off.
•
When you remove a compute sled containing a PERC controller with mappings, and replace it with a new compute sled having an HBA
330 controller with a different service tag, a message is displayed on the
Devices
>
Compute
>
Overview
page for the compute
sled, prompting you to clear or accept the mapping. However, the compute sled is turned on in this scenario.
The following flowchart and table illustrate the behavior of OME-Modular and the LCD panel on the chassis when the compute sled is
replaced:
Figure 1. Compute sled replacement—flowchart
Table 17. Compute sled replacement - Behavior of OME-Modular and LCD panel
OME-Modular behavior
LCD behavior
Case 1
Enables users to clear all mappings to the
compute sled.
Enables users to clear all mappings to the
compute sled.
Case 2
Enables users to clear or retain all mappings
to the compute sled.
Enables users to clear or retain all mappings
to the compute sled.
Viewing compute hardware
You can view the details of the hardware components that are installed in the compute sled, on the compute
Hardware
page. The
hardware components include processor, storage controller, and FRU.
The deployment and configuration jobs on the compute sled are performed only for the first time, if the profile and sled device ID are
unchanged. If the sled is removed and reinserted, the deployment and configuration job is not performed. This condition is applicable to
the
Edit Profile
task too.
NOTE:
If the storage controller cards are absent in iDRAC, the storage enclosure details are not displayed on the
Compute > View Details > Hardware > Storage Enclosure page.
Viewing compute firmware
You can view the firmware list for the compute in the compute
Firmware
page. Click
Devices
>
Compute
>
View Details
>
Firmware
.
The details include name of the device or component, impact assessment, current version, and baseline version.
You can perform the following tasks on the Firmware page:
Managing compute sleds
51