Dell PowerVault TL4000 Dell Model TL24iSCSIxSAS 1Gb iSCSI to SAS - User's G - Page 50

Adding a Target portal, Advanced Discovery Settings

Get Dell PowerVault TL4000 PDF manuals and user guides View all Dell PowerVault TL4000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Appendix C To add an iSCSI Target portal, click on 'Add Portal'. The user should now be presented with a window as in Figure 33. Figure 33 Adding a Target portal Enter an IP-address for the iSCSI Target. In this example we shall use the IP-address of 10.10.10.50. Leave the port 3260 unless you have configured your iSCSI bridge only to respond on port 860, in which case change it to 860. Click on the advanced button to see the advanced options. This is shown in Figure 34. Figure 34 Advanced Discovery Settings The 'Connect by using' box allows the user to specify which iSCSI Adaptor to use and the Source IP. The Local adaptor will only differ from Microsoft iSCSI Initiator setting if an iSCSI Offload card has been installed. For the purpose of this guide we shall only use the Microsoft iSCSI Initiator. Leaving this setting as Default will also use the Microsoft iSCSI Initiator. The Source IP is used to specify upon which network adaptor the discovery will be done. In most cases the user will want to leave this as default. If multiple network interfaces are installed in the Server and the user wishes to select a particular interface, select the IP-address of that network interface from the pull down list. Page 48 Dell Model TL24iSCSIxSAS 1Gb iSCSI to SAS User's Guide Rev.C

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
Appendix C
Page 48
Dell Model TL24iSCSIxSAS 1Gb iSCSI to SAS User’s Guide
Rev.C
To add an iSCSI Target portal, click on ‘Add Portal’.
The user should now be presented with a window as in
Figure 33.
Figure 33 Adding a Target portal
Enter an IP-address for the iSCSI Target.
In this example we shall use the IP-address of 10.10.10.50.
Leave the port 3260 unless you have configured your iSCSI bridge only to respond on port 860, in which
case change it to 860.
Click on the advanced button to see the advanced options.
This is shown in Figure
34.
Figure 34 Advanced Discovery Settings
The ‘Connect by using‘ box allows the user to specify which iSCSI Adaptor to use and the Source IP.
The
Local adaptor will only differ from Microsoft iSCSI Initiator setting if an iSCSI Offload card has been installed.
For the purpose of this guide we shall only use the Microsoft iSCSI Initiator.
Leaving this setting as Default
will also use the Microsoft iSCSI Initiator.
The Source IP is used to specify upon which network adaptor the discovery will be done. In most cases the
user will want to leave this as default.
If multiple network interfaces are installed in the Server and the user
wishes to select a particular interface, select the IP-address of that network interface from the pull down list.