Epson ActionTower 8100 User Manual - Page 105

Reconnecting the Dlskette Drive Cables, the drive's connector. Then push in the connector.

Get Epson ActionTower 8100 PDF manuals and user guides View all Epson ActionTower 8100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 105 highlights

Reconnecting the Dlskette Drive Cables Refer to the illustration below while you follow the steps in this section to reconnect cables to the diskette drive. 1. Locate the connector you will use on the diskette drive cable. 2. Identify pin 1 on the drive and align the connector so that the red wire is at pin 1. Push in the connector. 3. Locate the power supply cable with the small connector. 4. Position the power supply cable connector so that the holes fit over all the pins and the red wire aligns with pin 1 on the drive's connector. Then push in the connector. 5. If you have finished installing or removing drives, replace the computer's cover; see "Replacing the Cover" in Chapter 4 for instructions. Then see "Running SETUP" in Chapter 2 for instructions on defining your new drive configuration. Installing and Removing Drives in the Slimline Computer 5-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
Reconnecting the Dlskette Drive Cables
Refer to the illustration below while you follow the steps in this
section to reconnect cables to the diskette drive.
1.
2.
3.
4.
5.
Locate the connector you will use on the diskette drive cable.
Identify pin 1 on the drive and align the connector so that
the red wire is at pin 1. Push in the connector.
Locate the power supply cable with the small connector.
Position the power supply cable connector so that the holes
fit over all the pins and the red wire aligns with pin 1 on
the drive’s connector. Then push in the connector.
If you have finished installing or removing drives, replace
the computer’s cover; see “Replacing the Cover” in Chapter
4
for instructions. Then see “Running SETUP” in Chapter 2
for instructions on defining your new drive configuration.
Installing and Removing Drives in the Slimline Computer
5-11