Epson ActionTower 8400 User Manual - Page 102

Connecting the Hard Disk Drive Cables, Locating the System Board Components in

Get Epson ActionTower 8400 PDF manuals and user guides View all Epson ActionTower 8400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

Connecting the Hard Disk Drive Cables After you replace the bracket, you need to connect the cables to the hard disk drive. Follow these steps: 1. Locate one of the IDE device cables that are connected to the IDE interfaces on the system board. They are flat cables with a connector at one end and two IDE device connectors at the other end. A red wire is on one side of the cable. (See "Locating the System Board Components" in Chapter 4 to find the primary and secondary IDE interfaces on the system board.) system board connector IDE device connectors red wire Use the primary IDE interface for your boot drive and your second hard disk drive; use the secondary IDE interface to connect IDE CD-ROM drives, other IDE devices, or your third and fourth hard disk drives. You cannot connect a CD-ROM drive and hard disk drive to the same interface. 2. Identify the IDE device connector you will use on the IDE device cable. 3. Locate pin 1 on the drive connector. If you do not see it on the connector casing and you did not locate it before you replaced the drive bracket, you may have to remove the drive and turn it over to check the circuit board. 5-8 Installing and Removing Drives in the Slimline Computer

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
Connecting the Hard Disk Drive Cables
After you replace the bracket, you need to connect the cables to
the hard disk drive. Follow these steps:
1.
Locate one of the IDE device cables that are connected to
the IDE interfaces on the system board. They are flat cables
with a connector at one end and two IDE device connectors
at the other end. A red wire is on one side of the cable. (See
“Locating the System Board Components” in Chapter 4 to
find the primary and secondary IDE interfaces on the
system board.)
system board
IDE device
connector
connectors
red wire
Use the primary IDE interface for your boot drive and your
second hard disk drive; use the secondary IDE interface to
connect IDE CD-ROM drives, other IDE devices, or your
third and fourth hard disk drives. You cannot connect a
CD-ROM drive and hard disk drive to the same interface.
2.
Identify the IDE device connector you will use on the IDE
device cable.
3.
Locate pin 1 on the drive connector. If you do not see it on
the connector casing and you did not locate it before you
replaced the drive bracket, you may have to remove the
drive and turn it over to check the circuit board.
5-8
Installing and Removing Drives in the Slimline Computer