HP 3600dn HP Jetdirect Print Server Administrator's Guide - Page 34

Using RARP

Get HP 3600dn - Color LaserJet Laser Printer PDF manuals and user guides
UPC - 829160888897
View all HP 3600dn manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

NOTE If you choose to re-enable a DHCP configuration, the print server will acquire its configuration information from a DHCP server. This means that when you choose DHCP and complete your configuration session (using Telnet, for example), the TCP/IP protocol for the print server is re-initialized and all current configuration information is deleted. The print server then attempts to acquire new configuration information by sending DHCP requests on the network to a DHCP server. For DHCP configuration through Telnet, refer to Using Telnet in this chapter. Using RARP This section describes how to configure the print server using the Reverse Address Resolution Protocol (RARP) on UNIX and Linux systems. This setup procedure enables the RARP daemon running on your system to respond to a RARP request from the HP Jetdirect print server and to supply the IP address to the print server. 1 Turn the printer off. 2 Log onto your UNIX or Linux system as a superuser. 3 Make sure the RARP daemon is running on your system by typing the following command at the system prompt: ps -ef | grep rarpd (UNIX) ps ax | grep rarpd (BSD or Linux) 4 The system response should be similar to the following: 861 0.00.2 24 72 5 14:03 0:00 rarpd -a 860 0.00.5 36 140 5 14:03 0:00 rarpd -a 5 If the system does not display a process number for the RARP daemon, see the rarpd man page for instructions on starting the RARP daemon. 6 Edit the /etc/hosts file to add your designated IP address and node name for the HP Jetdirect print server. For example: 192.168.45.39 laserjet1 7 Edit the /etc/ethers file (the /etc/rarpd.conf file in HP-UX 10.20) to add the LAN hardware address/station address (from the configuration page) and the node name for the HP Jetdirect print server. For example: 00:01:E6:a8:b0:00 laserjet1 NOTE If your system uses Network Information Service (NIS), you need to incorporate changes to the NIS host and ethers databases. 8 Turn the printer on. 9 To verify that the card is configured with the correct IP address, use the ping utility. At the prompt, type: 26 Chapter 3 TCP/IP Configuration ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
NOTE
If you choose to re-enable a DHCP configuration, the print server will acquire its
configuration information from a DHCP server. This means that when you choose DHCP and
complete your configuration session (using Telnet, for example), the TCP/IP protocol for the
print server is re-initialized and all current configuration information is deleted. The print server
then attempts to acquire new configuration information by sending DHCP requests on the
network to a DHCP server.
For DHCP configuration through Telnet, refer to
Using
Telnet
in this chapter.
Using RARP
This section describes how to configure the print server using the Reverse Address Resolution
Protocol (RARP) on UNIX and Linux systems.
This setup procedure enables the RARP daemon running on your system to respond to a RARP
request from the HP Jetdirect print server and to supply the IP address to the print server.
1
Turn the printer off.
2
Log onto your UNIX or Linux system as a superuser.
3
Make sure the RARP daemon is running on your system by typing the following command at the
system prompt:
ps -ef | grep rarpd
(UNIX)
ps ax | grep rarpd
(BSD or Linux)
4
The system response should be similar to the following:
861 0.00.2 24 72 5 14:03 0:00 rarpd -a
860 0.00.5 36 140 5 14:03 0:00 rarpd -a
5
If the system does not display a process number for the RARP daemon, see the
rarpd
man page
for instructions on starting the RARP daemon.
6
Edit the
/etc/hosts
file to add your designated IP address and node name for the HP Jetdirect
print server. For example:
192.168.45.39 laserjet1
7
Edit the
/etc/ethers
file (the
/etc/rarpd.conf
file in HP-UX 10.20) to add the LAN
hardware address/station address (from the configuration page) and the node name for the HP
Jetdirect print server. For example:
00:01:E6:a8:b0:00 laserjet1
NOTE
If your system uses Network Information Service (NIS), you need to incorporate
changes to the NIS host and ethers databases.
8
Turn the printer on.
9
To verify that the card is configured with the correct IP address, use the ping utility. At the
prompt, type:
26
Chapter 3
TCP/IP Configuration
ENWW