HP 3600dn HP Jetdirect Print Server Administrator's Guide - Page 46

SNMP Traps, Other, 100FULL, 100HALF, Support, Web JetAdmin URL

Get HP 3600dn - Color LaserJet Laser Printer PDF manuals and user guides
UPC - 829160888897
View all HP 3600dn manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Table 3-3 Telnet Commands and Parameters (continued) SetRequest must match the print server's "set community name" for the print server to respond. (For additional security, you may limit configuration access through the print server's host access list.) Community names must be ASCII characters. The maximum length is 255 characters. default-get-cmnty Enables or disables the default Get community name. 0 disables, 1 (default) enables. Disabling this parameter may prohibit communications with SNMP management applications. SNMP Traps auth-trap trap-dest Other link-type Support Web JetAdmin URL Web JetAdmin Name support-contact support-number Configures the print server to send (on) or not send (off) SNMP authentication traps. Authentication traps indicate that an SNMP request was received, but the community name check failed. 0 is off, 1 (default) is on. Enters a host IP address into the HP Jetdirect print server's SNMP trap destination list. The command format is: trap-dest: ip-address [community name] [port number] The default community name is 'public'; the default SNMP port number is '162'. The port number cannot be specified without a community name. To delete the table, use 'trap-dest: 0'. If the list is empty, the print server does not send SNMP traps. The list may contain up to three entries. The default SNMP Trap Destination List is empty. To receive SNMP traps, the systems listed on the SNMP trap destination list must have a trap daemon to listen to those traps. Sets the print server's link speed (10, 100 Mbps) and communication mode (Full- or Half-Duplex). The available link-speed selections depend on the print server model. The selections that may be displayed are listed below. CAUTION If you change the link setting, network communications with the print server and network device may be lost. AUTO (default): 100FULL: 100 Mbps, full-duplex operation. 100HALF: 100 Mbps, half-duplex operation. 10FULL: 10 Mbps, Full-duplex operation. 10HALF: 10 Mbps, half-duplex operation. (Read-only parameter) If HP Web Jetadmin discovers this device, the URL to access HP Web Jetadmin will be specified. (Read-only parameter) If HP Web Jetadmin discovers this device, the name of the HP Web Jetadmin host will be specified (if known). Typically used to identify the name of a person to contact for support of this device. Typically used to specify a phone or extension number to call for support of this device. 38 Chapter 3 TCP/IP Configuration ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
SetRequest must match the print server's “set community name” for the print server to
respond. (For additional security, you may limit configuration access through the print
server's host access list.) Community names must be ASCII characters. The maximum
length is 255 characters.
default-get-cmnty
Enables or disables the default Get community name.
0 disables, 1 (default) enables.
Disabling this parameter may prohibit communications with SNMP management
applications.
SNMP Traps
auth-trap
Configures the print server to send (on) or not send (off) SNMP authentication traps.
Authentication traps indicate that an SNMP request was received, but the community
name check failed. 0 is off, 1 (default) is on.
trap-dest
Enters a host IP address into the HP Jetdirect print server's SNMP trap destination list.
The command format is:
trap-dest:
ip-address [community name] [port number]
The default community name is ‘public’; the default SNMP port number is ‘162’. The
port number cannot be specified without a community name.
To delete the table, use ‘trap-dest: 0’.
If the list is empty, the print server does not send SNMP traps. The list may contain up
to three entries. The default SNMP Trap Destination List is empty. To receive SNMP
traps, the systems listed on the SNMP trap destination list must have a trap daemon to
listen to those traps.
Other
link-type
Sets the print server's link speed (10, 100 Mbps) and communication mode (Full- or
Half-Duplex). The available link-speed selections depend on the print server model. The
selections that may be displayed are listed below.
CAUTION
If you change the link setting, network communications with the
print server and network device may be lost.
AUTO
(default):
100FULL
: 100 Mbps, full-duplex operation.
100HALF
: 100 Mbps, half-duplex operation.
10FULL
: 10 Mbps, Full-duplex operation.
10HALF
: 10 Mbps, half-duplex operation.
Support
Web JetAdmin URL
(Read-only parameter) If HP Web Jetadmin discovers this device, the URL to access
HP Web Jetadmin will be specified.
Web JetAdmin Name
(Read-only parameter) If HP Web Jetadmin discovers this device, the name of the HP
Web Jetadmin host will be specified (if known).
support-contact
Typically used to identify the name of a person to contact for support of this device.
support-number
Typically used to specify a phone or extension number to call for support of this device.
Table 3-3
Telnet Commands and Parameters (continued)
38
Chapter 3
TCP/IP Configuration
ENWW