HP 680n HP Wireless Print Server 680n - (English) Setup Guide - Page 28

Factory-default Wireless Settings

Get HP 680n - JetDirect Print Server PDF manuals and user guides
UPC - 808736198622
View all HP 680n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Factory-default Wireless Settings The HP Jetdirect print server's wireless factory-default settings are shown in Table 3-1. Table 3-1 Factory default wireless settings Parameter Settings Comments Communications Mode Ad Hoc If your network uses an Access Point, you must reconfigure the Communications Mode of the Jetdirect print server to "Infrastructure". Channel 10 (Ad Hoc mode only) This specifies the broadcast channel if the print server fails to connect to a network. In most cases, you will not need to change this setting. The print server will scan all available channels for the specified network and will adapt its channel to the one detected. Network Name (SSID) hpsetup You must change the SSID on the print server to match your network. In Infrastructure mode, you must match the SSID configured on the Access Point. Authentication Open System The Jetdirect print server is not configured for network authentication. If required by your network, the proper authentication method must be configured on the Jetdirect print server. Encryption (WEP) If your network uses WEP encryption keys, you must configure the encryption keys on the print server. You can configure up to four WEP keys. The active key must match the value and active key position (for example, Key 1) configured on other wireless devices. 3-2 Making a Wireless Network Connection

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
3-2 Making a Wireless Network Connection
Factory-default Wireless Settings
The HP Jetdirect print server’s wireless factory-default settings are
shown in Table 3-1.
Table 3-1
Factory default wireless settings
Parameter
Settings
Comments
Communications
Mode
Ad Hoc
If your network uses an Access Point, you
must reconfigure the Communications
Mode of the Jetdirect print server to
“Infrastructure”.
Channel
10
(Ad Hoc mode only) This specifies the
broadcast channel if the print server fails
to connect to a network. In most cases,
you will
not
need to change this setting.
The print server will scan all available
channels for the specified network and
will adapt its channel to the one detected.
Network Name (SSID)
hpsetup
You must change the SSID on the print
server to match your network. In
Infrastructure mode, you must match the
SSID configured on the Access Point.
Authentication
Open
System
The Jetdirect print server is not
configured for network authentication. If
required by your network, the proper
authentication method must be
configured on the Jetdirect print server.
Encryption (WEP)
<Disabled>
If your network uses WEP encryption
keys, you must configure the encryption
keys on the print server. You can
configure up to four WEP keys. The
active key must match the value and
active key position (for example, Key 1)
configured on other wireless devices.