HP 680n HP Wireless Print Server 680n - (English) Setup Guide - Page 71

Table C-1, HP Jetdirect Classic Control Panel Menu 4 of 6

Get HP 680n - JetDirect Print Server PDF manuals and user guides
UPC - 808736198622
View all HP 680n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Table C-1 HP Jetdirect Classic Control Panel Menu (4 of 6) Menu Item CFG 802.11B= (continued) TCP/IP= IPX/SPX= DLC/LLC= ATALK= Description ● ENCRYPT: For static WEP encryption, this item appears if AUTH.=OPEN (Open System) , AUTH.=SHARED (Shared Key), or EAP-MD5=ON. Choose an encryption level: ■ 128 for 104/128-bit encryption ■ 64 for 40/64-bit encryption ■ NONE (default). ● TX KEY: This item appears if you selected 128- or 64-bit encryption and is used to specify the active transmit key. Choose one of the transmit encryption key positions (key 1, 2, 3, or 4). The selected transmit key must have a valid WEP key value assigned. If a valid WEP key is not assigned, the first key found with a valid key will be assigned. ● CFG KEY #: Use this menu to configure key values for up to four key positions (where # identifies the key). ■ NO (default): Bypass configuration of this key. ■ YES: Configure a key value for this key. The format for entering key values is hexadecimal entries with alphanumeric assist. Hexadecimal digits (0 - 9, A - F) are entered one byte (two digits) at a time, and an alphanumeric character for that value will be displayed. For 40/64-bit encryption, enter 5 bytes (10 digits). For 104/ 128-bit encryption, enter 13 bytes (26 digits). ● 802.11B: Choose to keep or reset the 802.11b wireless parameters on the print server. ■ KEEP: Configured parameters are maintained. ■ RESET: Parameters will be reset to factory-default values. Parameter values for other network protocols are not reset. To view the reset values, you must exit and reenter the control panel menu. Identifies whether the protocol stack is enabled or disabled. ● ON (default): The protocol is enabled. ● OFF: The protocol is disabled. HP Jetdirect EIO Control Panel Menus C-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
HP Jetdirect EIO Control Panel Menus C-5
CFG 802.11B=
(continued)
●
ENCRYPT: For static WEP encryption, this item appears
if AUTH.=OPEN (Open System) , AUTH.=SHARED
(Shared Key), or EAP-MD5=ON. Choose an encryption
level:
■
128 for 104/128-bit encryption
■
64 for 40/64-bit encryption
■
NONE (default).
●
TX KEY: This item appears if you selected 128- or 64-bit
encryption and is used to specify the active transmit key.
Choose one of the transmit encryption key positions (key
1, 2, 3, or 4). The selected transmit key must have a valid
WEP key value assigned. If a valid WEP key is not
assigned, the first key found with a valid key will be
assigned.
●
CFG KEY #: Use this menu to configure key values for up
to four key positions (where # identifies the key).
■
NO (default): Bypass configuration of this key.
■
YES: Configure a key value for this key.
The format for entering key values is hexadecimal entries
with alphanumeric assist. Hexadecimal digits (0 - 9, A - F)
are entered one byte (two digits) at a time, and an
alphanumeric character for that value will be displayed.
For 40/64-bit encryption, enter 5 bytes (10 digits). For 104/
128-bit encryption, enter 13 bytes (26 digits).
●
802.11B: Choose to keep or reset the 802.11b wireless
parameters on the print server.
■
KEEP: Configured parameters are maintained.
■
RESET: Parameters will be reset to factory-default
values. Parameter values for other network protocols
are not reset. To view the reset values, you must exit
and reenter the control panel menu.
TCP/IP=
IPX/SPX=
DLC/LLC=
ATALK=
Identifies whether the protocol stack is enabled or disabled.
●
ON (default): The protocol is enabled.
●
OFF: The protocol is disabled.
Table C-1
HP Jetdirect Classic Control Panel Menu (4 of 6)
Menu Item
Description