HP D2D .HP D2D Backup System user guide (EH985-90907, March 2011) - Page 46

Network configuration, 1Gb and 10Gb ports HP D2D4300 Series only - netbios

Get HP D2D PDF manuals and user guides View all HP D2D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Network configuration The details in this section reflect the IP settings that were specified during installation. The HP StoreOnce Backup System supports DHCP for IPv4 networks and this is turned on by default. NOTE: NetBIOS name resolution is not supported on CIFS shares. You may need to edit the details if there is a conflict in the IP address, or you move the host to a different network node. Be aware that any changes you make to the network settings could affect how you connect again to the HP StoreOnce Backup System. For example, if you change the IP address, you must use the new address to log in from a web browser. 1Gb and 10Gb ports (HP D2D4300 Series only) The HP D2D4300 Series has two 1Gb ports and two 10Gb ports. You must connect to the 1Gb port (labeled LAN port 3) to run the Installation Wizard and discover the HP StoreOnce Backup System on your network. This is also the recommended port for running the Web Management Interface. The 10Gb ports are available for backup and replication traffic. Take care if configuring with DHCP because the HP StoreOnce Backup System supports only one gateway address. If 1Gb and 10Gb 46 Appliance Configuration

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
Network configuration
The details in this section reflect the IP settings that were specified during installation. The HP StoreOnce
Backup System supports DHCP for IPv4 networks and this is turned on by default.
NOTE:
NetBIOS name resolution is not supported on CIFS shares.
You may need to edit the details if there is a conflict in the IP address, or you move the host to a
different network node. Be aware that any changes you make to the network settings could affect
how you connect again to the HP StoreOnce Backup System. For example, if you change the IP
address, you must use the new address to log in from a web browser.
1Gb and 10Gb ports (HP D2D4300 Series only)
The HP D2D4300 Series has two 1Gb ports and two 10Gb ports. You must connect to the 1Gb port
(labeled LAN port 3) to run the Installation Wizard and discover the HP StoreOnce Backup System
on your network. This is also the recommended port for running the Web Management Interface.
The 10Gb ports are available for backup and replication traffic. Take care if configuring with DHCP
because the HP StoreOnce Backup System supports only one gateway address. If 1Gb and 10Gb
Appliance Configuration
46